LID opportunities in industrial, commercial and multi-residential types

The site types considered in this guide are grouped into six general categories based upon site similarities:

• High and mid-rise
• Low rise
• Light industrial
• Large commercial
• Small commercial
• Institutional

If the listed site features do not unanimously apply to your site, select the most appropriate category or use a combination of two or more categories to screen LID options. Please note that LID practices are scalable and applying alternate LID practices to those identified for each land use group may be a possibility upon a more detailed evaluation of site constraints (i.e. field testing conducted during pre-design). Choosing an appropriate LID practice can be an iterative process as additional site information becomes available in the predesign phase.

For each land use group, this section identifies source areas typically found on these sites. Source areas are features such as parking lots, roofs, pedestrian areas, common areas, and landscape areas. The section also discusses LID retrofit opportunities and constraints within these source areas, and provides a table for each land use group that identifies common, possible, and unlikely retrofit options.

High-rise and mid-rise sites

Mid- and high-rise sites (four storeys or more) share common features. These buildings are often for residential use and include apartments or condominiums. They may be operated by residential leasing companies or condominium associations. Many office buildings belong to this site category. Office buildings may be operated by an independent site owner, but they are often owned and operated by commercial land management groups.

Mid- and high-rise buildings have higher user occupancy densities than other sites and therefore require significant parking area. To conserve the site area, these parking areas are typically located underground. Mid- and high-rise buildings most commonly have flat roofs that drain internally to onsite storm sewer networks. These sites typically have common areas, but their size and function vary.

Common areas

Pedestrian and common areas are outdoor features that can be found on most mid- and high-rise sites. They provide access and egress to buildings and allow pedestrian movement around the property. Most mid- and high-rise buildings will have common areas at their entrance that can include garden features, planters and benches. On residential sites, common areas may include parks or parkettes, playgrounds, sports facilities, sidewalks, and pathways.

Landscaped areas

Landscaped areas commonly surround mid- and high-rise buildings They can also be found adjacent to parking lots and internal roads. These areas are often grassed and may include plantings. Landscaped areas are ideal for establishing bioretention areas, soakaways, or bioswales where conveyance is preferred. If grading allows, landscaped areas adjacent to the parking lot can easily be retrofitted to provide quality control and water balance benefits. Landscaped areas may also be located within the pedestrian areas adjacent to a building. These areas can be targeted to accept and infiltrate clean roof drainage. Cisterns for rainwater harvesting can also be located in these areas, either buried or above ground. Utilities may be buried within landscaped areas on your site (not just adjacent to the building). Locates are required before digging occurs.

Roof areas

In most municipalities, the rooftops of mid- and high-rise buildings are not very visible. Developing LID practices on these surfaces will provide benefits but will be more difficult to promote. The exception is major urban centres where a significant number of high rises have been developed and sometimes look onto each other.

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

A shallow excavated surface depression containing prepared filter media, mulch, and planted with selected vegetation.

Linear bioretention cell designed to convey, treat and attenuate stormwater runoff. The engineered filter media soil mixture and vegetation slows the runoff water to allow sedimentation, filtration through the root zone, evapotranspiration, and infiltration into the underlying native soil.

The accounting of inflow and outflow of water in a system according to the components of the hydrologic cycle.

Natural or artificial means of intercepting and removing surface or subsurface water (usually by gravity).

Tank used to store rainwater (typically roof runoff) for later use.

The practice of intercepting, conveying and storing rainwater for future use. Captured rainwater is typically used for outdoor non-potable water uses such as irrigation, or in the building to flush toilets.