Inspection and Maintenance: Rainwater Harvesting

Inspection & Maintenance Guidance of Rainwater harvesting/cisterns best management practices. Rainwater harvesting is the practice of collecting, storing and making use of stormwater from roofs. Relatively clean roof runoff water is collected by eavestroughs or other types of roof drains, filtered to remove coarse debris, and conveyed to a structure where it is stored and drawn upon for purposes not requiring potable water (i.e. landscape irrigation, outdoor washing needs, fire suppression and toilet flushing (TRCA, 2018).

Overview

Rainwater harvesting/cisterns uses storage structures that can be installed either:

• Below-ground;
• Indoors that provide a year-round water source; or,
• Aboveground tanks and rain barrels that can only be used seasonally and must be taken out of service for the winter.

Rainwater cisterns can range in size from about 750 to 40,000 litres+ and may be constructed from fiberglass, plastic, metal or concrete. Underground cisterns are most often installed to a depth below the maximum frost penetration depth (generally 1.2 m in Southern Ontario) (Armstrong and Csathy, 1963; Ministry of Transportation, 2013) to ensure they can be used year-round. A pump is used to deliver the stored water to the hose bibs or fixtures where it is utilized. Water that is in excess of the storage capacity of the cistern overflows to an adjacent drainage system (e.g., other BMP or municipal storm sewer) via an overflow outlet structure and pipe. Cisterns that are drawn upon for indoor water uses (e.g., toilet flushing) will also feature water level sensors and the means of adding municipal water during extended periods of dry weather or winter when stormwater does not meet the demand (i.e., make-up water supply system). They may also include in-line devices to filter stored cistern water prior to delivery at hose bibs or fixtures.

Generalized cross-section view of a rainwater harvesting system showing key components of a commercial configuration of this LID BMP (TRCA, 2018).

Some of the benefits of green roofs include:

• The ability to reduce the quantity of pollutants and runoff being discharged to municipal storm sewers and receiving waters (i.e., rivers, lakes and wetlands);
• Underground and indoor cisterns can be used year-round and located below parking lots, roads, plazas, parkland, landscaped areas or within buildings themselves.
• Can reduce a large commercial building or residential home's water usage significantly if used for non-potable needs
  

Key components of Underground Infiltration Systems to pay close attention to are the:

• Inlets
• Rain Barrel or Cistern|
• Pump
• [Pretreatment

Associated Practices

• Rain Barrels Rain barrels are an above ground form of rainwater harvesting, typically used in residential settings. The precipitation flows from the roof, to the guttering and down the downspout before being diverted to the rain barrel for storage.
• Downspout disconnection Downspout disconnections are common in many older urban centers. They require that residents retroactively disconnect their downspouts from the municipal sewer system. This is due to older sewer systems being undersized for the combined flow of sanitary waste and stormwater.
• [[Blue roofs) are systems that temporarily capture rainwater using the roof as storage and allow it to evaporate and/or to be used for non-potable requirements (i.e. irrigation, toilet flushing, truck washing) and ultimately offset potable water demands.

State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include Source, Conveyance and End-Of-Pipe Controls.

The practice of intercepting, conveying and storing rainwater for future use. Captured rainwater is typically used for outdoor non-potable water uses such as irrigation, or in the building to flush toilets.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

Human application of water to agricultural or recreational land for watering purposes. City of Toronto Wet Weather Flow Management November 2006 47

Toronto and Region Conservation Authority

Tank used to store rainwater (typically roof runoff) for later use.

Tank used to store rainwater (typically roof runoff) for later use.

A system flow of gully inlets, pipes, overland flow paths, open channels, culverts and detention basins used to convey runoff to its receiving waters. City of Toronto 45 Wet Weather Flow Management November 2006

Best management practice. State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include: source, conveyance and end-of-pipe controls.

Tank used to store rainwater (typically roof runoff) for later use.

The practice of intercepting, conveying and storing rainwater for future use. Captured rainwater is typically used for outdoor non-potable water uses such as irrigation, or in the building to flush toilets.

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

Watercourses and Lake Ontario, to which Stormwater and Combined Sewer Overflows discharge.

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

Any form of rain or snow.

Surface runoff from at-grade surfaces, resulting from rain or snowmelt events.

State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include Source, Conveyance and End-Of-Pipe Controls.