Inspection and Maintenance: Underground Infiltration Systems

Inspection & Maintenance Guidance of underground infiltration systems' best management practices that refers to LIDs that capture and temporarily store rainwater and snowmelt from hard surfaces (e.g., roofs and pavements) below ground in geotextile filter fabric lined excavations filled with washed gravel or other void space forming structures (TRCA, 2018)

Overview

Underground infiltration systems is a general term that refers to best management practices (BMPs) that capture and temporarily store stormwater from hard surfaces. These systems treat stormwater by detaining it to allow suspended sediments to settle out and soaking it into the ground where it is filtered and cleansed by interaction with soil. Runoff water is delivered to the practice through pipes connected to catchbasins, hydrodynamic (i.e., oil and grit) separators, filters, manholes, sub-drains of other features or roof downspouts. They are installed below the local maximum frost penetration depth to ensure they continue to drain year-round. Water that is in excess of the storage capacity overflows to an adjacent drainage system (e.g., municipal storm sewer or other BMP), typically via pipe or manhole containing a control structure (e.g., weir wall), to safely convey flows during flood events. Depending on the permeability of the underlying soil, such practices may be designed without a sub-drain for full infiltration or with a sub-drain for partial infiltration. The sub-drain pipe may feature a flow restrictor (e.g., orifice cap, valve) for gradually releasing detained water and optimizing the amount drained by infiltration.

General plan and profile (cross-section) views showcasing key components and sections of a typical infiltration trench.

Key components of Underground Infiltration Systems to pay close attention to are the:

• Inlets
• Sub-Drains
• Monitoring Wells
• Overflow outlets

Trash, debris and sediment builds up at these locations and can prevent water from flowing into or out of the practice.

Associated Practices

• Soakaways: Typically service individual lots and receive only roof and walkway runoff but can also be designed to receive overflows from other BMPs (e.g., rain barrels or cisterns, rain gardens, green roofs. Also known as infiltration galleries, French drains, dry wells or soakaway pits.
• Infiltration trenches: Linear oriented soakaways designed to fit into narrow strips of land between structures or properties, or along road rights-of-way; can also receive road runoff with adequate pretreatment devices upstream of inlets.
• Infiltration chambers: Include a range of proprietary modular structures installed underground that create large void spaces for temporary storage of stormwater while providing sufficient load bearing capacity to allow construction of structures on top of them. Applications are similar to infiltration trenches. Also known as infiltration tanks or vaults.
• Perforated pipe storm sewer systems or Exfiltration trenches: Linear-oriented infiltration trenches installed parallel with conventional storm sewer pipes and catchbasins that receive stormwater from them. May include manholes with perforated risers. Also known as exfiltration storm sewer, percolation drainage, or clean water collector systems.

State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include Source, Conveyance and End-Of-Pipe Controls.

Toronto and Region Conservation Authority

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

A system flow of gully inlets, pipes, overland flow paths, open channels, culverts and detention basins used to convey runoff to its receiving waters. City of Toronto 45 Wet Weather Flow Management November 2006

Best management practice. State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include: source, conveyance and end-of-pipe controls.

The slow movement of water into or through a soil or drainage system.

Penetration of water through the ground surface.

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

An underground water storage reservoir into which stormwater is directed and allowed to percolate into the underlying native subsoil.

An excavated area lined with geotextile filter cloth and filled with clean granular stone or other void forming material, that receives runoff and allow it to infiltrate into the native soil; can also be referred to as infiltration galleries, French drains, dry wells or soakaway pits.

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

The downward movement of water through the soil, the downward flow of runoff from the bottom of an infiltration BMP into the soil.

Loss of water from a drainage system as a result of percolation or absorption into the surrounding medium (e.g., the infiltration of water into the native soil through a perforated pipe wall as it is conveyed).

Natural or artificial means of intercepting and removing surface or subsurface water (usually by gravity).

State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include Source, Conveyance and End-Of-Pipe Controls.