This article is about large, building-integrated rainwater harvesting systems. For smaller, seasonal, outdoor systems, see Rain barrels
Rainwater harvesting (RWH) is the ancient practice of collecting and storing precipitation for later use. Although Ontario is a region with relatively abundant fresh water, RWH is increasing in popularity for a number of reasons:
- The simplicity of selecting and installing a system, owing to improvements in the technology and the development of a local industry,
- The ease of modelling RWH in a stormwater management (SWM) plan, owing to the fixed size of the catchment and the cistern,
- Increasing transparency of storm sewer costs in some municipalities, and
- Increasing utility rates for potable water supply.
Take a look at the downloadable Rainwater Harvesting Factsheet below for a .pdf overview of this LID Best Management Practice:
Rainwater harvesting is an ideal technology for:
- Sites which cannot infiltrate water owing to contaminated soils or shallow bedrock,
- Zero-lot-line developments such as condos or dense urban infill, or conversely
- Projects with extensive gardens and landscapes which would benefit from free irrigation water.
The fundamental components of a rainwater harvesting system are:
- the catchment area where the rain lands (e.g. rooftop),
- a screen or filter to remove coarse debris (mostly leaves),
- a cistern which will store the collected rainwater and preserve its quality,
- the connecting pipe network including roof drains.
Additional components may include:
- pumps to lift water to higher elevations, depending on the layout of the components,
- additional water filtration and treatment, depending on the intended use of the water.
Place in the Treatment Train
To maximize the volume of water available for reuse, a RWH system is usually located near to the front of a treatment train. i.e. Upstream of other LID technologies. The most common exception would be where a site strategy employs a green roof. A simple warm-weather system may capture all of the rooftop runoff in an external tank above grade and use it for sub-surface irrigation. In this scenario the tank can overflow via gravity to a sub-surface infiltration chamber or a bioretention cell. But, if the tank is located below the ground or inside a building the overflow may need a pump.
The origin of the harvested water affects the permissible end uses. Some of the most common uses include irrigation and flushing or toilets and urinals. As mixed source water can only be applied to the more limited end uses, selecting the catchments for a RWH system requires careful consideration.
- The Ontario Building Code (OBC) regulates the use of harvested rainwater as one of many non-potable water sources. "Rainwater means storm sewage runoff that is collected from a roof or the ground, but not from accessible patios and driveways."
- The CSA standard B805-18/ICC805-2018 separates "roof runoff" from all other sources, including landscaped areas and green roofs. Collectively green roofs, landscaped and paved areas result in "stormwater runoff."
The current disparity between these two definitions affects all vegetated landscapes including green roofs. Confusion over terminology and regulation has been identified as a significant barrier to implementation of RWH since 2010.
Cistern and Pipework
Cisterns must be installed in locations where native soils or the building structure can support the load associated with the volume of stored water.
Expansion caused by freezing water will damage pipes, pumps and the cistern. There are two options for managing a RWH system in our climate:
- The entire system is drained and closed off ahead of sub-zero temperatures
- All pipework, pumps, filters and the cistern are protected from freezing during the winter
The first option may be suitable for systems optimized for exterior irrigation only. But regulatory authorities may not permit the use of such seasonal systems as part of a storm water control strategy. Year round systems can be protected from freezing by locating the pipes, pumps and cistern indoors and/or below the frost penetration depth.
Design for Maintenance
Detailed inspection and maintenance advice can be found in Sustainable Technologies' LID I&M guide. The two primary operational concerns for RWH systems are:
- A leak developing,
- Debris obstructing some part of the plumbing.
Planning can help ensure that these are identified and fixed more easily and cheaply. Example questions:
- Is the roof (catchment) readily accessible to sweep debris periodically?
- Could the accumulation of debris on the roof be reduced by removing any overhanging branches?
- Can the leaf screens accessed from the roof? Or from a maintenance room?
- Will the cistern require entry for inspection in the future? How will this be accessed?
RWH systems producing higher quality water will have additional maintenance requirements. These will depend on the the treatment technologies being used.
In a recent international research literature review on urban rainwater harvesting systems, Campisano et al. (2017) note that degree of implementation and design choices are strongly influenced by economic constraints (need for low cost, easy to retrofit systems) and government regulations (need for policies, standards and guidelines that ensure system efficacy and improve community acceptance), and that systems tend to be designed for water conservation alone, without considering co-benefits like helping to achieve stormwater management objectives.  Adequately sizing rainwater harvesting systems is critical to optimizing their operation because under-sizing results in systems that are unable to provide sufficient, reliable sources of water while oversizing increases the capital costs incurred and poses potential water quality risks if stored water remains unused for long periods of time. In a recent research literature review, Semaan et al. (2020) identified sizing for water storage as most important for system optimization, yet found that sizing for cost is a more frequently implemented optimization approach. They note several sizing and optimization approaches and tools are available globally. 
Follow the link below for detailed guidance on approaches to sizing rainwater harvesting systems in Ontario.
Rainwater Harvesting: Sizing and Modelling
Decisions need to be made about the selection and grading of catchments. If one catchment is very large, can it be regraded to drain to two or more outlets? Is it desirable to capture both rooftop water and other stormwater? This will may determine the quality improvements required to use the water. See table below, which illustrates the higher treatment required for storm water (i.e. non-rooftop).
Preformed above-ground tanks are usually constructed from polyethylene or galvanized steel. They are available with storage capacity up to around 50,000 L. Preformed below-ground tanks may be constructed from reinforced fiberglass or concrete. Fiberglass tanks are available up to around 150,000 L. Concrete vaults can be constructed in almost any size. Wooden tanks are less common but are also available and permitted in the regulations. As a standing body of freshwater, RWH cisterns present ideal habitat for mosquitoes. Mosquitoes should be prevented from entering by using a mesh screen on all openings. Larvicides may be added when the water is only to be used for irrigation purposes. To prevent algal growth, the cistern must be opaque or otherwise protect the water from light.
Plumbing and Regulation
The current Ontario Building Code requires that rainwater harvesting systems are designed, constructed and installed to conform to good engineering practice. References are made to ASHRAE, ASPE and CSA  guides for plumbing detailing. These guides focus on ensuring that the rainwater does not contaminate or become mistaken for the municipal drinking water supply. Similarly, rainwater must be prevented from becoming contaminated from the sewer. In both cases, an air gap or a back-flow preventer is required.
In theory a large enough RWH cistern could retain 100% of a single storm. However, sizing a stormwater cistern must account for regulatory requirements, available space, budget, and draw-down i.e. rate of use. If a RWH system is being employed for storm water control, the cistern size will typically be greater than that for optimized potable water use reduction.
In 2007-2010 STEP monitored and modelled three rainwater harvesting systems in the Greater Toronto Area. Each system was sized to balance stormwater management objectives with with potable water use reduction for irrigation and toilet flushing. Around 18-20% of the precipitation was lost directly from the rooftop, and the annual stormwater capture varied between 18 and 42 %.
Take a look at the Rainwater Harvesting: Performance page by clicking below for further details about STEPs collected performance results for Permeable pavement and Porous Asphalt practices located within TRCA's, CVC's and LSRCA's watersheds:
The important water quality parameters for harvested rainwater differ from other types of LID. This is due to the potential for direct human contact, rather than environmental discharge. As of July 2017, the CSA and ICC are finalizing a standard which specifies different water quality treatments according to the source (roof runoff versus stormwater runoff) and the intended use.
Tier 1 end uses are most readily achievable, requiring only that larger particles are filtered out of the water. Removing the bulk of the solid particles reduces the nutrient concentration in the water and prevents clogging of the water distribution system. Toilet and urinal flushing are the next most popular use of harvested rainwater. If flushing or other higher tier end uses are desired, disinfection of some type is required and consideration may be given to colour and odour of the water. Technologies for achieving higher standards of water quality include:
- Ultraviolet (UV) disinfection requires additional filtration to remove particles so that the light can penetrate the water and destroy the viruses and bacteria,
- Chlorine disinfection also requires additional filtration to remove larger particles,
- Micro- or Ultra- filtration uses such fine membranes that the vast majority of harmful viruses, bacteria etc. are excluded from the water directly.
All three water purification technologies require specialist design and consultation with a subject matter expert is recommended for higher tiers of water use.
|Application||Roof runoff pathogen reduction||Stormwater pathogen reduction|
|End Use Tier||Example uses||Viruses||Bacteria||Protazoa||Viruses||Bacteria||Protazoa|
|HVAC systems||In accordance with ASHRAE 188|
||0||99.999%||99.999%||Outside of the scope of the CSA standard|
Source Water Quality
A study of many types of roof surfaces in Texas found:
- 'Cool' membrane, concrete tile, and metal roofs all produced water of similar good quality for non-potable use,
- The runoff water from asphalt shingle and green roofs contained significantly more dissolved organic carbon (DOC). The DOC can add a yellow colour to the water. If the water is treated with chlorine, for drinking purposes, DOC can produce toxic compounds.
Research in Hamilton, ON assessed the water quality of rain collected from three highly reflective 'cool roof' membranes. Key findings:
- The water was free from significant contamination with by-products of plastic manufacture and did not show elevated levels of the five metals tested.
- Increased microbiological contamination was found in runoff from roof areas where ponding occurred.
Note: Increased microbiological contamination in roof runoff is also associated with warmer weather .
Incentives and Credits
City of Mississauga The City of Mississauga has a stormwater management credit program which includes RWH as one of their recommended site strategies.
LEED BD + C v. 4
Water Efficiency: Rainwater management (up to 3 points) Note that for lines 1. and 2. preference is given to LID that 'best replicates natural site hydrology':
- Two points (or 1 point for Healthcare) will be awarded if the project manages "the runoff from the developed site for the 95th percentile of regional or local rainfall events."
- Three points (or 2 points for Healthcare) will be awarded if the project manages "the runoff from the developed site for the 98th percentile of regional or local rainfall events."
For zero-lot-line projects only, 3 points (or 2 points for Healthcare) will be awarded if the project manages "the runoff from the developed site for the 85th percentile of regional or local rainfall events." This last clause relating to zero-lot-line projects is where RWH may prove most applicable compared to other LID.
Pilot Credits: Whole Project Water Use Reduction (up to 10 points) This pilot credit requires whole building water use modeling to demonstrate reduced water use compared to a baseline model. A sliding scale awards between 1 point for 10% reduction to 10 points for 65% reduction. Making this kind of water use reduction would typically require reuse of greywater as well as an optimized RWH plan.
Rainwater harvesting system design guides
- Canadian Standards Association (CSA) B805-18/ICC805-2018, Rainwater harvesting systems
- CMHC Guidelines for Residential Rainwater Harvesting Systems Handbook (2012)
- Ontario Rainwater Harvesting Guidelines (2010)
In our effort to make this guide as functional as possible, we have decided to include proprietary systems and links to manufacturers websites.
Inclusion of such links does not constitute endorsement by the Sustainable Technologies Evaluation Program.
Lists are ordered alphabetically; link updates are welcomed using the form below.
- Campisano, A., Butler, D., Ward, S., Burns, M.J., Friedler, E., DeBusk, K., Fisher-Jeffes, L.N., Ghisi, E., Rahman, A., Furumai, H., Han, M. 2017. Urban rainwater harvesting systems: Research, implementation and future perspectives. Water Research. 115 (2017) 195-209. https://www.sciencedirect.com/science/article/abs/pii/S0043135417301483?via%3Dihub
- Semaan, M., Day, S.D., Garvin, M., Ramakrishnan, N., Pearce, A. 2020. Optimal sizing of rainwater harvesting systems for domestic water usages: A systematic literature review. Resources, Conservation & Recycling: X 6 (2020) 100033. https://www.sciencedirect.com/science/article/pii/S2590289X20300049?via%3Dihub
- Mendez CB, Klenzendorf JB, Afshar BR, et al. The effect of roofing material on the quality of harvested rainwater. Water Res. 2011;45(5):2049-2059. doi:10.1016/j.watres.2010.12.015.
- Cupido, A., B. Baetz, Y. Guo, and A. Robertson. 2012. An evaluation of rainwater runoff quality from selected white roof membranes. doi: 10.2166/wqrjc.2012.011.
- Vialle C, Sablayrolles C, Lovera M, Jacob S, Huau MC, Montrejaud-Vignoles M. Monitoring of water quality from roof runoff: Interpretation using multivariate analysis. Water Res. 2011;45(12):3765-3775. doi:10.1016/j.watres.2011.04.029.