Salt

Excess salt located by a curb and next to a stormwater catch basin in a parking lot. Salt entering a catch basin is one of the many ways rock salt and elevated levels of chloride can enter the local freshwater system. Rock salt has major impacts on infrastructure, as it increases the rate of erosion/decay of supporting materials (rebar in concrete, etc.) and can lead to structural failure if overused (Wallace, et al. 2022). Photo Source: LSRCA, 2018.

Environmental & Health Impacts

A graph showing increasing average levels of chloride found in Lake Simcoe, and its watershed's rivers, streams and groundwater systems over the past few decades, due in part to increased use of rock salt in parking lots, roadways and commercial and residential properties. It is estimated that by 2120 the average level of chloride within the the Lake Simcoe watershed will exceed the 120mg/l guideline set by CWQG. (LSRCA, 2018)

Salt contamination in freshwater (freshwater salinization) is a major concern to Ontarians wellbeing as it can lead to:

• Unpleasant taste in drinking water
• Health issues for those with hypertension issues
• Health issues for those who have experienced congestive heart failure
• Impacts to those with sodium restricted diets

STEP's Technical Brief: Alternatives to Salt: What else melts snow and ice? from 2020, highlights how municipalities across Canada using salt as their primary de-icing agent in winter, poses significant impacts to their regions. This includes, corrosion of infrastructure and other metal structures such as railings and doorways, damage to vehicles, contamination of surface and groundwater, impacts to roadside vegetation, increased wildlife collision rates and large amounts of product waste due to blowing or bouncing off roadways). You can read more about the benefits, drawbacks, cost estimates and lowest working temperature for a given deicing agent at the link above.

Furthermore, salt can contribute to both biodiversity and habitat loss for numerous species. In Ontario, road salt was identified as one of the threats to drinking water under the Clean Water Act, 2006 - as well as a known toxin to wildlife species. Salt can impacts bird species, many plants and trees growth ability, and decrease size, function and fecundify in fish, mollusks (snail, mussels, etc.), amphibians and benthic invertebrate species.

A recent literature review by Hintz and Relyea (2019), discusses the impacts of road salt on local ecosystems and found that road salts negatively affect species at all trophic levels, from biofilms to fish species, but the concentration of road salt where adverse effects were observed varied and the effects themselves ranged from:

• Reductions in fecundity, size and shape of various species
• Reduced levels of growth and abundance of sensitive species
• Alterations to nutrient and energy flow at an ecosystem level
• Increased greenhouse gas emissions from contaminated wetlands; and,
• Altered hydrology, oxygen, nitrogen and carbon level dynamics in lakes and streams.

CCME Guidelines on Salt's Impact to Environment

The Chloride - Canadian Water Quality Guidelines for the Protection of Aquatic Life document from the Canadian Council of Ministers of the Environment (CCME) is another valuable paper that discusses the direct toxic effects of chloride, based on studies using NaCl and CaCl² salts. The guideline can be used as a screening and management tool to ensure that chloride does not lead to the degradation of the aquatic environment. Further guidance on the application of these guidelines is provided in the scientific criteria document (CCME 2011), which can be found here - Scientific Criteria Document - Cl Ion. The scientific criteria document goes into detail about the following related to chloride levels in the environment:

A study by researchers at Yale and Rensselaer Polytechnic Institute, in NY found the interactive effects of road salt on wood frog species' sex ratios and sexual size dimorphism. Over a series of experiments conducted, the authors of the paper in the Canadian Journal of Fisheries and Aquatic Sciences discovered that the number of females within the studied population of tadpoles decreased by ~10% when exposed to road salt. These findings suggest road salt may have a 'masculizing effect' on various amphibian species.

• Aquatic sources and fate
• Ambient concentration in Canadian waters, sediment and soils
  • broken down by province/region
• Toxicity of Chloride (Cl^-) to Aquatic life
  • Influences, short-term toxicity - long-term for vertebrates, invertebrates, and plants and algal species
• Effects of (Cl^-) on water quality parameters
  • Oxygen / Temperature / Hardness / Chloride and its association to other compounds and their toxicity
• Other Impacts
  • Mutations / Bioaccumulation / Dermal Effects / Taste and odour of water and fish

Recent Local Findings

Most recently, staff from the TRCA released an article in the January/February, 2022 edition of Water Canada magazine entitled, "Freshwater Salinization: Can we keep our freshwater fresh?", highlighting the effects of rock salt's over use and application across Southern Ontario's watersheds and its impact on freshwater environments and species.

Some of the key findings from the article highlight:

• In Ontario chloride concentrations (Cl^-) are measured monthly under the Provincial Water Quality Monitoring Network (PWQMN). Concentrations in the mouth of the Don River has showcased levels three times that of the Canadian Water Quality Guidance (CWQG) for long-term chronic effects to the environment and species.
• Although the PWQMN has ben an excellent tool for following the long-term trends of median concentration levels in the province's watersheds due to the infrequency of sampling, peak values will at times be missed, and extreme values and extreme values and outliers that result in excessive salt and chloride loadings in key areas with species at risk, etc.
• As a result, TRCA, along with its partners began a monitoring project at the mouths of the major tributaries within the GTA using high-frequency conductivity sensors, which make readings every 15 mins.
• Some of the results from their monitoring work found
  • Highland Creek: (Peak concentration of 8,400 mg/L) - 70 times the CWQG limit for chronic effects & 13 times the CWQG limit for acute effects of aquatic organisms.
  • Duffins Creek: (Peak concentration of ~3,000 mg/L) - 25 times the CWQG limit for chronic effects & ~5 times the CWQG limit for acute effects of aquatic organisms.
• These high concentrations pose a considerable threat to fish, aquatic organisms, and ecosystem health overall - especially considering the frequency and duration of these values in major watercourses in urbanized areas of the province. The findings highlight the need for increased water monitoring efforts and requirements for new sensor technology to capture an accurate representation of the current state of our rivers and streams. (Wallace, et al. 2022.)

Salt Alternatives

Due to rock salt's numerous impacts on both infrastructure and the environment numerous studies have been conducted to determine if there are adequate alternatives to the practice of salt application to parking lots and roads. These include sand, organic de-icing materials (agricultural by-products), and salt water brine to name a few.

Below find a summary table of common de-icers and alternatives in comparison to rock salt regarding lowest working temperature, cost estimations and average application rates.

Comparison of Commonly used De-icers

Deicer	Cost Estimate (low $ - high $$$$)	Typical Application Rates (average range)	Lowest Practical Working Temperature (°C)
NaCl (Rock Salt)	$	~130 kg/2 lane km, depending on conditions (range 70-220 kg/2-lane km in Lake Simcoe watershed)	-9
MgCl2 (Liquid Brine)	$$	Liquid anti-icing: 35-59 L/2-lane km	-15
CaCl2 (Liquid Brine)	$$$	Liquid anti-icing: 35-59 L/2-lane km	-29
Treated Rock Salt	$$	72-130 kg/2-lane km	-17
Calcium Magnesium Acetate	$$$$	219-292 kg/2-lane km (for first application, lower for subsequent due to residual effect)	-7
Agricultural By-Products	Varied Cost ($$ - $$$$)	Varies; often used to pre-wet rock salt – less salt is required, lowest effective temperature is reduced	-17 to -23

Agricultural By-Products & Brine

Many municipalities have found treated rock salt to be worth the extra investment, due to its increased effectiveness at lower temperatures and lower application rate when compared to standard rock salt application practices. The process of pre-wetting rock salt with brine or an agricultural by-product (beet juice for example) as it is applied can help the mixture better adhere to road and pavement surfaces better and reduce excess waste and can enhance the effectiveness of rock salt application below -12°C. To note, the effectiveness of agricultural by-products is still under some evaluation, as some major cities, including Toronto, use it under certain conditions, several Lake Simcoe watershed municipalities have tested it and found it not to be as effective as rock salt. Furthermore, agricultural by-products have to be applied before a snowfall event to melt the fallen snow in a relatively short period of time, which generally is not possible or practical (if applied after a snowfall event it takes a long time to begin the melting process). Read more about these alternative applications in STEP's Technical Brief: Alternatives to Salt.

Sand accumulates on the ride of the road after being applied after a snowfall event. Sand can travel into nearby watercourses, wetlands, and increases clean-up associated costs for the municipality. Photo source: LSRCA, 2018.

Detailed analysis of the performance of varying de-icer agents and liquid brine can be found in STEP's earlier technical brief entitled, Evaluation of Organic Anti-icing Materials for Winter Maintenance.. The document describes the practice of "anti-icing", (applying liquid brine solutions to paved surfaces before a winter storm) to help prevent ice and snow from bonding to the roadway surface, which in turn helps to reduce the amount of rock salt required to remove salt and ice. To read more, click the link above.

Sand

Property managers often turn to sand as an alternative to salt, as it is thought to be a less harmful option. Sand has been used, either on its own or mixed with salt, as a core part of many municipalities’ or individual property managers’ winter maintenance practices. It is used similarly to rock salt as it is applied to increase friction between snowy or icy pavement and the vehicles/pedestrians passing over it. Of those municipalities that use sand, rural ones with a higher proportion of gravel roads use almost exclusively sand (with a small percentage of salt mixed in to prevent freezing and caking), while other municipalities often use a sand-salt mix at various ratios

The general issues with sand are that:

• Most sand applied blows off the road within relatively few (e.g. 8-12) vehicle passes at speeds over 40 km/hr (general speed limits of most municipal subdivision streets); rendering any improvement in friction temporary, at best.
• Pre-wetting can help sand adhere to the road, but there is little to no increase in its friction coefficient even with this pretreatment approach.
• When sand mixes with melting snow it doesn't embed itself in the snow but rather becomes more of a slushy mixture that accumulates on the side of roads, or worse within SWM features (catch basins, stormwater ponds, etc.).
  • The associated cost municipalities incur as a result of sand accumulation along roadways, curbsides and in SWM features are due to the additional effort required (more frequent catchbasin cleanouts, etc.) and the cost of sweeping up this material at the end of each winter season to reduce ongoing environmental impacts.
• Due to contamination of sand, disposal is becoming a more complicated, and therefore costly process causing a number of municipalities to re-evaluate their winter maintenance programs, when it comes to using sand.

To read more about LSRCA's Technical Bulletin: Sand versus Salt document exploring the efficacy of the use of sand for winter maintenance, its associated environmental issues, and where its use is most appropriate, visit the link above.

Design Strategies for Salt Reduction

Each year, Canadians spend over $1 billion on public and private roads, parking lots and sidewalks (Hossain et al., 2015). While the use of salt is essential to ensure public safety, there is a growing concern regarding the large quantities of salt (mainly chloride ions), being released to the environment.

In their 2001 assessment under the Canadian Environmental Protection Act, it was found that high releases of road salts from winter maintenance activities were having an adverse effect on freshwater ecosystems, soil, vegetation, and wildlife (Environment Canada, 2001). Based on this conclusion, Environment Canada developed its “Code of Practice the Environmental Management of Road Salts,” which focuses mainly on municipal and provincial road maintenance. This code, which requires the development of Salt Management Plans for those organizations using more than 500 tonnes of road salt annually, was released by Environment Canada in 2004 (Environment Canada, 2004). While the uptake of this code of practice has been successful for municipalities, there is not a similar recognized guideline for parking lot contractors. That said, there are studies and training programs that address this issue, which aims to educate private contractors about best practices, and how these can improve their level of service, protect the environment, and reduce associated costs. However, uptake of these programs has been low. To address this gap, LSRCA and its partner agencies identified a need for a guideline document that could be used by designers, regulatory agencies, owners, contractors, and others to consider design elements in the design and layout of parking lots and related infrastructure that can help to reduce the requirement for salt application. This effort culminated in the development of LSRCA's Parking Lot Design Guidelines​

• LSRCA has created a landing page with their partners, which include three key documents:
  • Fact Sheet - Parking Lot Guidelines: Highlights the impacts of elevated chloride levels in freshwater systems in the Lake Simcoe watershed and detailed, bullet-point descriptions of how to design parking lots to limit over application of rock salt.
  • Parking Lot design Guidelines - Full Report: Written in partnership with GHD the Parking Lot Design Guidelines to Promote Salt reduction is the primary document LSRCA uses to provide background on the issue of over salting roads and parking lots, primary design features for owners and contractors to consider, case study and site examples where the guidelines have been followed and Drawings of these sites that can be found on the main Parking Lot Guideline landing page.
  • Municipal Policy Template: This template document aids municipalities in the drafting of their own parking lot design and salt reduction policy document based on the findings and design guidance from LSRCA's Parking Lot design Guidelines - Full Report, 2017.

The LSRCA's commissioned study with GHD describes preferred salt management design strategies for parking lots, which can be read here: LSRCA salt guide. The report identified four key design strategies. They can be seen summarized below:

Effective Grading

• Proper grading can minimize the freezing of wet pavement surfaces and prevent melt water from ponding and re-freezing, reducing the need for re-application of salt.
• Areas for vehicular and pedestrian traffic should be graded between 2 - 4 % to reduce the chances of depressions forming over time (maximum permitted 5% for AODA). Small depressions can result in ponded water icing over in the winter.
• Subbase should be well compacted for the same reason.
• In winter months efficient salt application should be made along the top of slopes; melting snow will carry the salt solution down-gradient.
• Effective grading can also direct melt water towards strategically placed stormwater collection infrastructure (i.e. catch basins, vegetated swales, bioretention features, landscaped areas), preventing salt application in heavy traffic areas that are also pathways for runoff.
• The key to effective stormwater collection during winter is to ensure that melt water from high traffic areas or snow piles does not have to travel great distances to a collection point..

Snow Pile Location

Not quite well graded enough; the puddle in the foreground will refreeze overnight.

• Snow piles should be strategically located to minimize the risk of melt water draining across high traffic areas and refreezing.
• Storage locations for snow piles should be around the outer edges of parking lots and downgradient from high traffic areas, in sunny areas where possible to accelerate melting.
• Consider grading the storage location to distribute the melt-water as sheet flow over a grass filter strip into an adjacent BMP, such as a bioretention cell or infiltration trench. In some cases, with careful vegetation selection and adequate drainage, the BMP itself can serve as a snow storage location. Designing specific drainage collection features for snow piles can ensure that melt water is quickly collected in the vicinity of the pile to reduce the opportunity for refreezing.
• Snow storage areas should be clearly marked for seasonal maintenance staff..

Sidewalk Design and Pedestrian Flow

• The design process should consider that pedestrians typically follow the path of shortest distance and do not necessarily use designed walkways. Walkways from adjacent residential areas and transit stops should be prioritized, and unnecessary walkways should be avoided.
• Sidewalks that receive infrequent use could be closed for the winter season.
• Maintained sidewalks should be ≥ 1.5 m wide to accommodate plowing and minimize the salting required.
• Using textured pavers can improve grip for pedestrians, again reducing the salt required.
• In busy areas around building entrances, covered walkways and heated mats also reduce salt requirements..

Landscaping Features

Trees

• Landscaping features (i.e. vegetated swales or landscaped islands) can lead to a reduced requirement of salt application by reducing the amount of paved surface.
• Specifying deciduous trees along walkways and near snow piles will maximize winter sunlight penetration. This will naturally enhance the melting of frozen surfaces, limiting the need for winter maintenance.
• Coniferous trees can be used to create treed wind breaks along the site perimeter to avoid snow drifts..

Other vegetation

Picture showing an empty parking lot after a winter storm. An example of an area that could be closed off to users reducing the need for salting or other maintenance practices (shoveling, plowing services, etc.)

Vegetation varies in its reaction to soils with high salinity:

• Salt in soil water generally makes it more difficult for roots to take up water. This phenomenon mimics drought conditions for the plant.
• If passing traffic sprays salty water onto plants it can reduce cold hardiness in buds and new twigs. These then become more susceptible to freezing, mortality or deformation.
• In high enough concentrations, sodium and chloride can also be directly toxic to plants. In some species the ions are absorbed by the plant and build up in the leaves causing them to die.

Generally, the vegetation growing closest to the source will be most strongly affected by salt. Plants actively growing in late winter (when salt levels are highest) are also more significantly affected. So, warm season grasses offer an advantage over cool season grasses, because they emerge later in the spring when excess salt has been flushed away. Resilient turf grasses are particularly useful in the design of vegetated filter strips, dry ponds and enhanced grass swales. The Ministry of Transportation have standardized a number of grass mixes. The 'Salt Tolerant Mix' is of particular value for low impact development applications alongside asphalt roadways and paved walkways.

Canada #1 Ground Cover (salt tolerant mix)

Common name	Scientific name	Proportion
Tall Fescue	Festuca arundinacea	25 %
Fults Alkali Grass	Puccinellia distans	20 %
Creeping Red Fescue	Festuca rubra	25 %
Perennial ryegrass	Lolium perrenne	20 %
Hard Fescue	Festuca trachyphylla	10 %

Example of three brine holding tanks that can reuse meltwater from salt induced snowmelt to be reused on a pavement surface i na high traffic area. These systems are generally built with corrosion-free materials to maximize the product's lifetime. Photo Source: Camion™

Other Design Features

Other options that can be considered to reduce the amount of salt that needs to be applied in a parking lot include:

• The use of permeable pavers: these improve drainage and prevent melt water from ponding and refreezing.
• Seasonally closing parking areas: many parking lots have areas that are infrequently used outside of the holiday shopping period. These areas can be closed and not maintained through much of the winter season, reducing both the effort and amount of salt required.
• Shaded Canopies: With roof canopies over major pedestrian walkways and entrances from parking lots to building enclosures, little to no snow or ice will fall in these high-traffic areas, resulting in reduced salt application. Consideration should be taken for the runoff generated from the canopy stormwater or snowmelt when weather begins to warm to limit the potential for of ponding/refreezing on the walkway.
• Conductive Pavement on Walkways/Entrances: Conductive pavements consist of electrically and thermally conductive materials mixed with the dielectric aggregates typically found in standard asphalt and concrete pavements. Once connected to a power or heat source, these pavements conduct electricity and emit heat to pavement surfaces, melting ice and snow with constant and uniform heat.
• Brine holding tanks: Collection of first flush (high chloride concentration) melt water runoff from a salt induced snowmelt (as opposed to rain and temperature induced snowmelt) has the potential to be beneficial if captured and reused as an anti-icing or pre wetting solution. In order to collect the first flush runoff, an electronically actuated valve controlled by an electrical conductivity sensor would be installed at the desired conveyance point to divert and collect the high chloride concentration runoff into a brine holding tank. The brine holding tank would be placed below ground and a pump could be connected to pump the brine solution into an anti-icing tank or directly used to pre-wet rock salt.

Procurement Guidance

Summary of Salt Reduction Measures and their estimated impact on salt use and contract costs from STEP's Procurement Guidance for Parking Lot Snow and Ice Management

Contracts for snow and ice management on private parking lots are typically oriented towards ensuring that plowing and salting promotes safe conditions throughout the winter, and that interruptions to regular business operations are kept to a minimum. The first thought of many people may be that applying more salt is safer for their patrons and workers but, applying more than is necessary not only harms the environment, as previously mentioned but also shortens the life of parking lot surfaces and can accelerate the process of corrosion of nearby buildings or transportation infrastructure on site, not to mention the extra cost of unnecessary road salt application. Property owners, businesses and contractors have control over how much salt is applied through their snow and ice management contracts, and the diligence with which they manage and oversee these contracts. The Procurement Guidance for Parking Lot Snow and Ice Management by STEP describes various clauses and conditions that can be considered by these groups to be included in contracts to promote the responsible use of road salts. A summary of the measures are provided in with estimates of the impact on salt use, and the potential influence these may have on contract costs.

Procurement Best Practices

Businesses can help reduce over-salting by ensuring that rock salt during the winter months is applied responsibly on parking lots and walkways. An easy way to do this is by ensuring that your snow and ice maintenance contract includes provisions requesting that industry best practices be employed and that associated operators are adequately trained.

Some BMP for procurement for rock salt application services include:

1. Effective Pricing of Services: Contract pricing by a lump sum by season or a fixed sum per event (with extra costs associated with standby time) are commo9n, but a combination of both payment options in the contract may create a financial incentive for both the parking-lot owner and salt operator to require less salt.
2. Accurate Salt Delivery: Updated and well-maintained salt application devices (i.e. salt spreaders) that can be calibrated to function and apply salt automatically based on the speed of the vehicle can greatly reduce the amount of rock salt applied and can better digitally track the amount used as well.
3. Reducing Liability Risk: Ensuring records and evidence of when, where and how plowing and salting practices were performed on site better protect the owner of the parking lot and contractor who applied the practices from potential slip and fall lawsuits.
4. Efficient Application: Consideration of pre-wetting or anti-icing with liquid salt brine before events will help accelerate the melting process during and after an event and help salt better adhere to the road/parking lot surface.
5. Consideration of Chloride Alternatives: Alternatives previously mentioned on this page such as acetates, formates, agricultural by-products (beet juice) can be used instead of rock salt (where feasible) or can be used as an anti-icing / pre-wetting agent.
6. Well Informed Decision Making Processes: Use of local weather forecasts, up-to-the-minute road information systems, internet based radar tracking and infrared thermometers to determine pavement temperatures can better decision making options that save time on salt, contractor crew capacity and money.
7. Trained Professionals: Requesting evidence of experience and requiring training and certification through the Ontario Smart about Salt Program will help to ensure that the contractor selected and property management staff have the skills necessary to implement best practices for road salt application.

To learn more about STEP's Salt Application Best Practices document for Winter Maintenance Contracts click on the hyperlink.

Parking Lot Friction Testing

LSRCA's Technical Bulletin: Alternatives to Salt is a valuable technical brief which covers BMPs that have been developed specifically for winter maintenance in parking lots. Along with recommendations around the proper use and calibration of equipment, many of these practices relate to plowing the lot and walkways before applying salt, and applying the recommended amount of salt for the conditions. Several studies have been conducted, by industry and academia, to determine what the “right” amount is, and, while “proper” application can vary depending on temperature and conditions. This report talks about main considerations contractors face in maintaining parking lots in winter:

• what application rate should be used?
• what is the level of service expected by the client, for which the bare pavement return time is a common measure?
• In order to better understand these questions; in 2017 the LSRCA obtained a friction tester, with a goal of quantifying the effectiveness of various practices and salt application rates. LSRCA’s friction testing showed that bare pavement is safest, as it has the highest friction value, and that the over-application of salt does not translate to safer conditions. To read more about the friction tester results continue on below, through the rest of this section.

Two of the main considerations contractors face in maintaining parking lots in winter are: what application rate should be used; and what is the level of service expected by the property owner, for which the bare pavement return time is a common measure (this is the amount of time it takes after treatment to achieve a bare surface). To better understand these questions in 2017 the LSRCA obtained a friction tester, with a goal of quantifying the effectiveness of various practices and salt application rates. Here we present some of the findings of this study.

This image demonstrates the two extremes of LSRCA’s friction testing: a perfectly clear and dry surface, with a µ value of 0.9 and the same surface covered in a light layer of snow, with a µ of only 0.11.

As can be seen in the inset table, the unit for measuring friction is ‘µ’, and the closer to 1.00 the µ value, the safer the surface. A high µ, however, is not the only measure of safety – many smooth indoor floors will have low µ values, in the range of 0.3 to 0.4, and they are generally not considered unsafe. Through this study, friction of several different surfaces, which received varying treatments was measured by LSRCA staff.

Friction Values and Related Road Surface Conditions

Measured Friction Value (µ)	Road Surface Condition
0.8 - 1.00	Dry, New Asphalt
0.50 - 0.80	Wet Asphalt
0.30 - 0.50	Wet Sand on Ice
0.25 - 0.30	Dry Sand on Ice
0.25 - 0.25	Dry Ice
0.05 - 0.15	Wet Ice

Friction values for a properly treated surface (left) with a small amount of residue (µ =0.63) and an over salted surface right, which has a much lower friction value (µ =0.26).

High volumes of salt are often applied because contractors, property managers, and parking lot users feel that the more salt there is, the safer the surface is to walk or drive on. However, a surface that has been treated at an appropriate rate, (which is slightly wet with a small amount of salt residue) has a much higher friction value (μ); with the level of service achieved far more efficiently, than when compared to the same surface where rock salt has been heavily applied (over salted).

The picture above shows the same walkway where more than 10 times the generally recommended amount of salt was applied in the photo on the left, and only shoveling was done in the photo on the right, and both µ values were in the low 0.20s.

Through this work, as referenced above - LSRCA staff documented higher friction values on untreated surfaces than on surfaces with large volumes of product; the µ value of a surface may remain low if it has only been shoveled or plowed. While shoveling is an important part of the winter maintenance process, practitioners need to consider the site and predicted conditions on a day-to-day basis to determine how to attain the safest surface for vehicle and foot traffic. In many cases the sun or traffic may melt the residual snow on a shoveled or plowed surface without any further treatment being necessary (saving both time and money); while in other cases, some salt, applied at an appropriate rate, may be necessary.

Higher Costs, Little Benefit

Friction testing has demonstrated that bare pavement is safest, as it has the highest friction value, and that the over-application of salt does not always translate to safer conditions. Simply put, applying salt at the prescribed rate for the conditions and shoveling or plowing where appropriate will attain a higher friction rate than an overapplication of salt.

What is a reasonable amount of time to achieve the desired level of service?:

• Depending on the operating hours of the property being maintained, it may be possible to reduce the salt application rate without sacrificing the desired level of service.
  • For example, many commercial properties keep hours between 9:00 am and 9:00 pm, which would mean that the lot does not need to be clear until shortly before 9:00 am. The table below demonstrates the time it would take to reach bare pavement at typical industry-recommended application rates, in a situation where the temperature is between -7 and -9 °C, with between 0.5 and 1.5 cm of snow on the ground. The rate may need to be increased or decreased slightly to achieve the desired level of service depending on varying factors related to traffic, sunlight, type of snow, and/or pavement type.

Time to Reach Bare Pavement Scenario Comparison

Difference Among Scenarios	Time to bare pavement (hrs)	Application Rate (g/m2)	Volume of salt used for each application (kg)*	Total salt applied/season (tonnes)**	Material costs/season (assuming $100/tonne)
Scenario 1	2	87	13,050	913	$91,300
Scenario 2	3	58	8,700	609	$60,900
Difference	1	29	4,350	304	$30,400

As the "Time to Reach Bare Pavement Scenario Comparison" above demonstrates, significant salt and cost savings could be seen in a typical big box store, commercial business or institutional building's parking lot by simply reducing the application rate of rock salt and extending the time to bare pavement by one hour. To note, this is only the material cost of the salt (which varies, but has been higher than $100/tonne in recent years (Tumilty, 2018). Over-application of salt has been noted to cause significant damage to parking lot infrastructure, including issues with concrete, corrosion of railings, damage to landscaping materials, and damage to interior buildings' flooring. Reducing the application rate would decrease the rate at which this damage occurs, as a result helping to minimize the amount needed to repair or replace at a given property each year. All of this without sacrificing the safety of parking lot users.

External links

Smart About Salt training program teaches winter contracting company staff and facility management staff how to appropriately apply rock salt and still being mindful about its environmental impact, all while reducing reducing liability and maintenance costs. To learn more, click the picture above.

• Smart about Salt
  • The website of the Smart About Salt Council (SASC) that offers training, recommendations, research and up to date new articles about the importance of proper management and use of rock salt on Ontario roadways, parking lots, private and residential properties. Training is offered in both English and French.

• Salt Application Verified Equipment (SAVE) Program: Managing Risk While Saving Money
  • The Salt Application Verified Equipment (SAVE) Program was developed to make the process of applying salt less subjective and encourage contractors providing snow and ice management services for parking lots and sidewalks to apply salt more efficiently. Through the program, salt spreading equipment is calibrated according to a standard test procedure, and contractors undertake in-field training to ensure familiarity with how to operate their equipment in a manner that achieves pre-determined target salt application rates. Equipment operators obtain annually renewable license and plate stickers to confirm that their equipment has been verified. The list of contractors with calibrated equipment is made available on-line for facility managers, property owners and property management companies to use in the procurement of snow and ice maintenance contracts for their properties. To learn more about the program click Here. And for further updates to the program's verification process visit SASC's page here.

• Good Practices for Winter Maintenance in Salt Vulnerable Areas. .
  • This guidance is a living document to help address the impacts of road salt, within specific vulnerable areas, and will be reviewed every two years to remain current with technological and legislative changes. There are several types of ‘salt vulnerable areas’, with various environment and human health goals including drinking water quality, wetland health, and fisheries that are identified within the document. This guidance currently prioritizes certain areas where municipal drinking water sources are known to be impacted by road salt, know as, ‘Issue Contributing Areas’ (ICAs) delineated under the Clean Water Act (2006).

• Winter Parking Lot and Sidewalk Maintenance Manual
  • The purpose of this manual By the Minnesota Pollution Control Agency (MPCA) is to deliver practical advice to those managing parking lots and sidewalks and help make proactive, cost-effective, environmentally conscious choices in winter parking lot and sidewalk management in the State of Minnesota. This knowledge will provide the opportunity to become a leader in the industry by operating more efficiently and reducing environmental impacts. The manual is based on the Minnesota Snow and Ice Control Field Handbook for Snowplow Operators, produced by the Minnesota Local Technical Assistance Program Center, and on the training materials for the MPCA's Winter Maintenance of Parking Lots and Sidewalks training class.

• A review of the species, community, and ecosystem impacts of road salt salinisation in fresh waters. .
  • This review study of the impacts of road salt on local ecosystems by Hintz and Relyea (2019), found that road salts negatively affect species at all trophic levels, from biofilms to fish species but the concentration of road salt where adverse effects were observed varied and the effects themselves ranged from reductions in fecundity, size and shape to alterations to nutrient and energy flow at an ecosystem level and increased greenhouse gas emissions from contaminated wetlands and altered hydrology and oxygen, nitrogen and carbon level dynamics in lakes and streams. concentration at which road salt triggered an effect varied considerably. To read mroe about their findings, click the link above.

• Hamilton Salt Management Plan.
  • The City of Hamilton's 2021 Salt Management Plan is intended to set out a policy and procedural framework for ensuring that the Municipality continuously improves the management of road salt used in its winter maintenance operations. The plan is dynamic and allows the City to phase in new approaches and technologies in a way that is responsive to fiscal demands and the need to ensure that roadway safety is not compromised. To read more about the City's finalized plan that compares it's current practices to BMPs, opportunities for improvement and achievement metrics which can be replicated fore other Ontario municipalities click the link above.

Proprietary Systems

In our effort to make this guide as functional as possible, we have decided to include proprietary systems and links to manufacturers websites. Inclusion of such links does not constitute endorsement by the Sustainable Technologies Evaluation Program.

• Camion™ - Salt brine holding tank systems for liquid salt brine storage.

Ground depression acting as a flow control and water treatment structure, that is normally dry.

(1) The wearing away of the land surface by moving water, wind, ice or other geological agents, including such processes as gravitation creep; (2) Detachment and movement of soil or rock fragments by water, wind, ice or gravity (i.e. Accelerated, geological, gully, natural, rill, sheet, splash, or impact, etc).

Lake Simcoe Region Conservation Authority

The drainage area of a river.

An area of land that drains into a river or a lake. The boundary of a watershed is based on the elevation (natural contours) of a landscape.

The water below the surface, and typically below the groundwater table.

A biological community, including humans and their natural environment.

Refers to the conditions in which an organism lives and survives or the conditions in which an organism resides. These conditions can be described as aspects of a “physical”, “social” or an “economic” environment, depending on the perspective perceived by the observer.

Refers to the conditions in which an organism lives and survives or the conditions in which an organism resides. These conditions can be described as aspects of a “physical”, “social” or an “economic” environment, depending on the perspective perceived by the observer.

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

Toronto and Region Conservation Authority

Mineral particles which are smaller than 2 mm, and which are free of appreciable quantities of clay and silt. Coarse sand usually designates sand grains with particle size between 0.2 and 0.02 mm.

Mineral particles which are smaller than 2 mm, and which are free of appreciable quantities of clay and silt. Coarse sand usually designates sand grains with particle size between 0.2 and 0.02 mm.

Sustainable Technologies Evaluation Program

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

Stormwater Management

Ground depression acting as a flow control and water treatment structure, that is normally dry.

Box like underground concrete structure with openings in curb and gutter designed to collect runoff from streets and pavement.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

a gently sloping, densely vegetated areas that treat runoff as sheet flow from adjacent impervious areas. They function by slowing runoff velocity and filtering out suspended sediment and associated pollutants, and by providing some infiltration into underlying soils.

Best management practice. State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include: source, conveyance and end-of-pipe controls.

Natural or artificial means of intercepting and removing surface or subsurface water (usually by gravity).

A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

A mixture of mineral aggregates bound with bituminous materials, used in the construction and maintenance of paved surfaces.

A broad category of particulate material used in construction, including sand, gravel, crushed stone, slag, recycled concrete and geosynthetic aggregates, and available in various particulate size gradations.

The delivery of a disproportionately large load of pollutants during the early part of storms due to the rapid runoff of accumulated pollutants. The first flush of runoff has been defined several ways (e.g., 10 mm per impervious area).

Initial pulse of stormwater runoff which picks up the pollutants that have settled on surfaces during the dry period. The first flush contains the highest pollutant concentrations.

A mixture of mineral aggregates bound with bituminous materials, used in the construction and maintenance of paved surfaces.

A vegetated area such as a bog, fen, marsh, or swamp, where the soil or root zone is saturated for part of the year.