Inspection and Maintenance: Permeable Pavement

Inspection & Maintenance Guidance of a built vstormwater best management practices that treats the stormwater that falls on them and can be designed to also receive runoff from adjacent impermeable surfaces (e.g., pavements and roofs) as either sheet flow or from a pipe (e.g., roof downspout) connected to the washed gravel base, where captured water is temporarily stored in the base where it later soaks into underlying native soil or sent to a municipal stormsewer/other BMP via underdrains (TRCA, 2016)

Overview

Permeable Pavement Permeable pavements contain many small openings (i.e., joints or pores) that allow rainfall and snowmelt (i.e., stormwater) to drain through them instead of running off the surface as it does on impervious pavements like conventional asphalt and concrete. An overflow outlet is needed to safely convey flows during flood events. Depending on the permeability of the underlying soil and other constraints, the pavement may be designed with no sub-drain for full infiltration, with a sub-drain for partial infiltration, or with an impermeable liner and sub-drain for a no infiltration practice. The sub-drain pipe may feature a flow restrictor (e.g., orifice cap or valve) for gradually releasing detained water and optimizing the amount drained by infiltration into the underlying soil.

Key components of Permeable pavements to pay close attention to are the:

• Inlets
• Aggregates
• Choker layer
• Underdrains
• Pavement Surface
• Contributing Drainage Area
• Geotextile
• Overflow outlets

Associated Practices

• Permeable Interlocking Pavers (i.e., Block Pavers) – Precast modular units made of concrete, pervious concrete or rubber/plastic composite designed to create open joints between pavers that are filled with fine, washed aggregate and installed on an open graded aggregate (i.e., clear stone) base and sub-base.
• Permeable Interlocking Grid Systems (i.e., grid pavers) – Precast concrete or manufactured plastic grids with open cells that can be filled with aggregate or a mixture of sand, gravel and topsoil and planted with grass or low-growing ground covers and are installed on an open-graded aggregate base.
• Pervious Concrete – a rigid pavement installed on an open-graded aggregate base that uses a cementitious binder to adhere aggregate together, similar to conventional concrete, except that the fine aggregate component is minimized or eliminated which results in the formation of connected pores throughout.
• Porous Asphalt – a flexible pavement installed on an open-graded aggregate base that uses a bituminous binder to adhere aggregate together, similar to conventional asphalt, except that the fine aggregate component is minimized or eliminated which results in the formation of connected pores throughout.

Inspection and Testing Framework

Permeable articulated block system at the LSRCA headquarters in Newmarket, ON is designed for heavy loads. This example shows an appropriate pavement surface condition when conducting any of, construction, assumption, routine or verification inspections.

Visual Indicators Framework - Permeable Pavements

Component	Indicators	Construction Inspection	Assumption Inspection	Routine Operation Inspection	Verification Inspection
Contributing Drainage Area
	CDA condition	x	x	x	x
Perimeter
	BMP dimensions	x	x		x
Filter Bed
	Standing water		x	x	x
	Trash		x	x
Vegetation
	Vegetation cover	x	x	x	x
	Vegetation condition		x	x
	Vegetation composition	x	x	x
Underdrain & Monitoring Well
	Monitoring well condition	x	x	x	x
	Sub-drain/Perforated pipe obstruction		x		x
Outlets	Overflow outlet obstruction	x	x	x	x
Pavement Surface	Pavement surface condition		x	x
	Pavement surface sediment accumulation	x	x	x	x
	Control structure condition	x	x	x	x
	Control structure sediment accumulation	x	x	x	x

Permeable pavement in need of maintenance as excess sediment and unwanted vegetation growth has begun to occur near the perimeter of the installation. Source: (TRCA, 2016)..

Testing Indicators Framework - Permeable Pavements

Component	Indicators	Construction Inspection	Assumption Inspection	Routine Operation Inspection	Verification Inspection
Testing Indicators
	Surface infiltration rate testing		x		(x)
	Natural or simulated storm event testing		x		(x)
	Continuous monitoring		x		(x)
Note: (x) denotes indicators to be used for Performance Verification inspections only (i.e., not for Maintenance Verification inspections)

Construction Inspection Tasks

A Vacuum Truck used for permeable pavement maintenance, which sucks up excess sediment and fines trapped between the pores of block pavers. Conducting this maintenance regularly helps maintain the practice's optimal infiltration rate during large rain events. (Source: STEP).

Construction inspections take place during several points in the construction sequence, specific to the type of LID BMP, but at a minimum should be done weekly and include the following:

1. During site preparation, prior to BMP excavation and grading to ensure the CDA is stabilized and/or flow diversion devices are in place and confirm that construction materials meet design specifications
2. At completion of excavation and grading, prior to backfilling and installation of pipes to ensure depths, slopes and elevations are acceptable
3. At completion of installation of pipes, prior to completion of backfilling to ensure slopes and elevations are acceptable
4. After final grading, prior to surface course installation to ensure depths, slopes and elevations are acceptable
5. Prior to hand-off points in the construction sequence when the contractor responsible for the work changes (i.e., hand-offs between the storm sewer servicing, paving, building and landscaping contractors)
6. After every large storm event (e.g., 15 mm rainfall depth or greater) to ensure flow diversion devices are functioning and adequately maintained. View the table below, which describes critical points during the construction sequence when inspections should be performed prior to proceeding further. You can also download and print the table here
   

Permeable Pavements: Construction Inspections

Construction Sequence Step & Timing	Inspection Item	Observations*
Site Preparation - after site clearing and grading, prior to BMP excavation and grading	Natural heritage system and tree protection areas remain fenced off
	ESCs protecting BMP layout area are installed properly
	CDA is stabilized or runoff is diverted around BMP layout area
	BMP layout area has been cleared and is staked/delineated
	Benchmark elevation(s) are established nearby
	Construction materials have been confirmed to meet design specifications
BMP Excavation and Grading - prior to backfilling and installation of pipes/catchbasins	Excavated soil is stockpiled outside the CDA
	Excavation location, footprint, depth and slope are acceptable
BMP Installation – after installation of pipes/catchbasins, prior to completion of backfilling	Structural components (e.g., pavement base, curbs) installation is acceptable
	Impermeable liner installed correctly, if applicable
	Installations of sub-drain pipes (e.g., locations, elevations, slopes), standpipes/monitoring wells are acceptable
	Sub-drain trench dams installed correctly (location, elevation)
	Surface coarse installation (elevation, slope, monitoring wells) is acceptable

Routine Maintenance - Key Components and I&M Tasks

Regular inspections (twice annually, at a minimum) done as part of routine maintenance tasks over the operating phase of the BMP life cycle to determine if maintenance task frequencies are adequate and determine when rehabilitation or further investigations into BMP function are warranted.

Table below describes routine maintenance tasks for permeable pavements, organized by BMP component, along with recommended minimum frequencies. It also suggests higher frequencies for certain tasks that may be warranted for BMPs located in highly visible locations or those receiving flow from high traffic (vehicle or pedestrian) areas or those designed with higher than recommended impermeable drainage area to permeable BMP footprint area ratios (I:P ratios). Tasks involving removal of trash, debris and sediment and weeding/trimming of vegetation for BMPs in such contexts may need to be done more frequently (i.e., higher standards may be warranted).

Individuals conducting vegetation maintenance and in particular, weeding (i.e., removal of undesirable vegetation), should be familiar with the species of plants specified in the planting plan and experienced in plant identification and methods of removing/controlling noxious weeds. Key resources on these topics are provided below at the links provided:

• Agriculture and Agri-food Canada’s Weed Info database
• Ontario Ministry of Agriculture, Food and Rural Affairs’ Ontario Weed Gallery
• Ontario Ministry of Agriculture, Food and Rural Affairs’ Noxious Weeds In Ontario list
• Ontario Invasive Plant Council’s Quick Reference Guide to Invasive Plant Species
• Oregon State University Stormwater Solutions, 2013, Field Guide: Maintaining Rain Gardens, Swales and Stormwater Planters, Corvallis, OR.
• Plants of Southern Ontario (book), 2014, by Richard Dickinson and France Royer, Lone Pine Publishing, 528 pgs.
• Weeds of North America (book), 2014, by Richard Dickinson and France Royer, University of Chicago Press, 656 pgs.

Permeable Pavements: Key Components, Descriptions and Routine I&M Requirements

Comnponent	Description	Inspection & Maintenance Tasks	(Pass) Photo Example	(Fail) Photo Example
Contributing Drainage Area (CDA)	Area(s) from which runoff directed to the BMP originates; includes the pavement itself and any adjacent impermeable pavement or roofs that drain to it.	Remove trash, debris and sediment from pavements (biannually to quarterly) and eavestroughs (annually); Replant or seed bare soil areas as needed.	CDA has not changed in size or land cover. Sediment, trash or debris is not accumulating and point sources of contaminants are not visible.	Size of the CDA has changed from design assumptions (i.e. large asphalt area drains to a small portion of the permeable pavement). Evidence of surface ponding is visible.
Pretreatment	Devices or features that retain trash, debris and sediment; help to extend the operating life cycle; examples are eavestrough screens, catch basin inserts and sumps, oil and grit separators, geotextile-lined inlets, gravel trenches, grass filter strips and forebays.	Remove trash, debris and sediment annually to biannually or when the device sump is half full; Measure sediment depth or volume during each cleaning, or annually to estimate accumulation rate and optimize frequency of maintenance.	Although permeable pavers are generally considered pretreatment for other BMPs in a treatment train system, using eavestrough screens can act as pretreatment as they don't add to sediment build up and accumulation on the paver surface. (Photo Source: Guertin, 2010)	Build up of leads, sediment and leaf detritus in an eavestrough downspout disconnection leading to a permeable pavement surface. If not cleaned regularly this can lead to clogged pores between the pavers reducing the infiltration rate where the downspout deposits water onto the feature. (Photo Source: My Gutter Pro, 2021)
Inlets	Structures that deliver water to the BMP (e.g., impermeable pavement edges, pipes from roof downspouts or catchbasins).	Keep free of obstructions; Remove trash, debris and sediment biannually to quarterly; Make note of sediment depth or volume during each cleaning or annually to estimate accumulation rate and optimize frequency of maintenance	Impermeable pavement edges along the edge of the pervious concrete and impermeable asphalt graded so excess sheet flow is infiltrated down through the pores of the infiltration BMP. (Photo Source: Fairfax County, 2014)	Accumulated sediment, poor grading and vegetation is preventing stormwater from entering the swale. Sediment on the curb cut surface behind of the inlet indicates ponding is also occurring and is depositing water towards the permeable paver surface.
Pavement Surface	The surface of the pavement, including pavers/pavement, joints and edge restraints (e.g., curbs, edging); should not allow water to pond on the surface so any observation or evidence of surface ponding (e.g., sediment caking on the pavement) indicates a drainage problem.	Check for sediment, surface ponding, deformation, sink holes, damage and loss of joint fill; Remove trash regularly (biannually-quarterly); Grid systems with soil and grass fill are maintained like lawns; Sweep and vacuum interlocking and rigid pavements regularly (annually-biannually) with regenerative air/pure vacuum sweeper; Plow snow as needed and spread deicers sparingly during winter; Repair ruts or local sinking of 15 mm or greater over a 3 metre length, adjacent pavers or cracks in pervious concrete or porous asphalt are vertically offset by 5 mm or greater and paver joint fill is missing or below 15 mm from the paver surface.	No damage, displacement or sinking of the permeable surface is visible and there are no weeds growing between paver joints.	The pavement surface has sunk in local areas, creating a trip hazard and the potential for further damage from snow plowing and parked vehicles nearby.
Vegetation	Applies to grid paver systems only; a mixture of deep rooting perennial grasses or low growing ground covers, tolerant to both wet and dry conditions and salt (if receiving impermeable pavement runoff); roots uptake water and return it to the atmosphere, provide habitat for soil organisms that break down pollutants trapped in the soil and help maintain soil structure and permeability.	Grid systems with soil and grass fill are maintained like lawns; In the first 2 months water frequently (biweekly in the absence or rain) and as needed (e.g., bimonthly) over the remainder of the first growing season; Remove weeds and undesirable plants biannually to quarterly; Replace/reseed dead plantings annually to achieve 80% cover by the third growing season; Do not apply chemical fertilizers.	The vegetation cover on the permeable pavement is turf grass as specified in the final design and contains very few weeds. (Photo source: WEF).	The turf grass cover on the permeable walkway is not thriving in some areas and needs cutting in others. It is also impairing the aesthetic value of the BMP.
Overflow Outlet	Structures (e.g., catchbasin, curb-cut, swale) that convey flow that exceeds the storage capacity of the BMP to another drainage system (e.g., municipal storm sewer or other BMP).	Keep free of obstructions; Remove trash, debris and sediment biannually to quarterly.	The overflow outlet is free of damage and obstruction and functions as designed to safely convey excess water from the BMP.	The overflow outlet is obstructed with sediment which impairs its function to convey excess water from the BMP.
Sub-drain	Optional component; perforated pipe(s) surrounded by gravel and may be wrapped in geotextile filter fabric; installed in the base or sub-base gravel layer to collect and convey treated water to an adjacent drainage system or other BMP; may also include a flow restrictor.	Keep pipe and flow restrictor free of obstructions by flushing annually; Inspect flow restrictor regularly (e.g., biannually to quarterly).	The solid section of the sub-drain pipe is not obstructed by sediment, debris or roots and shows no signs of damage.	A section of the sub-drain pipe has been crushed which substantially reduces its conveyance capacity
Monitoring well	Perforated standpipe that extends from the bottom of the excavation to just below the pavement surface and contains perforations or slots to allow measurement of subsurface water level; used to track drainage performance over the operating life cycle of the BMP.	Standpipes should be securely capped on both ends and protected from damage by vehicular traffic by a casing.	The well is undamaged and accessible and the cap is in place and secured to prevent unauthorized access	The well cap is missing and the casing is clogged by sediment, preventing access for monitoring and allowing sediment to flow into the sub-drain system.
Control Structure	Manhole or catchbasin to which the subdrain outlets that provides access to the underdrain and flow restrictor. Inspect for accessibility, damage and sediment.	Remove trash, debris and sediment regularly (biannually/quarterly)..	TThere is some sediment accumulated in the manhole but it is not impairing the flow of stormwater into or out of the BMP. (Photo source: SWC Canada)	The manhole sump is full of sediment and debris and it is beginning to impair flow of stormwater into a perforated pipe of the exfiltration storm sewer system.

Tips to Preserve Basic BMP Function

• Never use sealants on porous asphalt nor pervious concrete.
• Prohibit access by construction vehicles to prevent tracking of sediment on to the surface.
• Prohibit storage of soil, compost, sand, salt or unwashed gravel on permeable pavements to prevent clogging of joints or pores, or protect the pavement surface with tarps or geotextile during temporary storage of such materials.
• Landscaped areas adjacent to permeable pavements should be covered with vegetation and not drain to the pavement where possible to prevent eroding soil from reaching the surface.
• Use a mulching mower to mow permeable interlocking grid systems with grass cover.
• Permeable pavements can be plowed for snow removal like conventional pavements. To reduce the risk of dislodging pavers or grids and minimize displacement of joint/cell fill material, the plow blade should be slightly raised off the pavement surface (e.g., 0.6 cm or 1/4”) with a shoe attachment.
• Plowed snow piles should not be stored on permeable pavements to reduce the risk of clogging from sediment accumulation upon melting.
• Do not spread sand on permeable pavements as part of winter maintenance as it will quickly clog the joints or pores and impair drainage function. On permeable interlocking pavers and grid systems filled with gravel, if application of an anti-skid material is desirable, spread the same fine washed gravel material used to fill the paver joints or grid cells; and
• De-icers should be used sparingly, as needed during winter. Due to their freely draining design, ice will not form on permeable pavements as readily as it does on conventional impermeable pavements during winter thaw-freeze cycles.

Rehabilitation & Repair

Table below provides guidance on rehabilitation and repair work specific to bioretention and dry swales organized according to BMP component.

Removign a section of pavers (where infiltration has decreased markedly, or all pavers (if necessary) should occur if surface drainage performance remains unacceptable. Joint fill and bedding layer will need be replaced at this point with new materials to help obtain initial design specifications (Photo Source: Western Interlock Inc., 2020)

Permeable Pavements: Key Components, Typical Issues and Rehabilitation Requirements

Component	Problem	Rehabilitation Tasks
Pavement Surface	Major cracks, spalling or raveling of the porous asphalt or pervious concrete surface	Fill small potholes or cracks with patching mixes (consult with product vendor for further guidance). Large potholes or cracks may require cutting and replacement of a section of the surface layer. Replace with the same permeable material where possible. Conventional asphalt or concrete could be acceptable if the cumulative area remains below 15% of the total BMP footprint area.
	Paver or grid unit is missing, damaged or displaced	Replace or reset unit by hand and restore joint or grid cell fill material that meets design specification.
	Surface infiltration rate is < 250 mm/h	Sweep and thoroughly vacuum with a pure vacuum sweeper to remove accumulated sediment. Replace joint fill material removed through vacuuming. Pretreatment of the surface of slow draining pavements (e.g., water-assisted techniques, additional sweeping) prior to vacuuming may be warranted where surface clogging of joints or pores is visible. If surface drainage performance remains unacceptable, remove all pavers, bedding and joint fill and top 5 cm (2”) of base aggregate and replace with new materials that meet design specifications.
Vegetation	Poor grass cover on interlocking permeable grid system	Aerate or remove and replace growing medium in affected area with material that meets design specifications and replant.
Sub-drain	Sub-drain perforated pipe is obstructed by sediment.	Schedule hydro-vac truck or drain-snaking service to remove the obstruction.

Inspection Time Commitments and Costs

Estimates are based on a typical partial infiltration permeable pavement design (i.e., includes a sub-drain); estimates for other designs (i.e., full infiltration and no-infiltration) are described in the Low Impact Development (LID) Stormwater Management Practice Inspection and Maintenance Guide

General time commitments and costs for inspection of permeable pavement features with partial infiltration design (in 2016 $ figures).

Per-task cost estimates for maintenance and rehabilitation of a partial infiltration bioretention feature (in 2016 $ figures).

Construction and life cycle cost estimates for permeable pavement features with partial infiltration design (in 2016 $ figures).

Estimates of the life cycle costs of inspection and maintenance have been produced using the latest version of the LID Life Cycle Costing Tool for three design variations (full infiltration, partial infiltration and no infiltration) to assist stormwater infrastructure planners, designers and asset managers with planning and preparing budgets for potential LID features.

Assumptions for the above costs and the following table below are based on the following:

• Design variations for permeable pavements can be broken down into three main categories:
  • Full Infiltration design, where the pavement drains through infiltration into the underlying subsoil alone (i.e., no sub-drain);
  • Partial Infiltration design, where drainage is through the combination of a subdrain and infiltration into the underlying subsoil (i.e., with a sub-drain); or,
  • No Infiltration (i.e., filtration only design) that includes an impermeable liner between the base of the BMP and the underlying native sub-soil, where drainage is through a sub-drain alone (i.e., with a sub-drain and impermeable liner).
• For permeable pavements it is assumed that rehabilitation of the pavement surface will be needed once the BMP reaches 30 years of age in order to maintain surface drainage performance at an acceptable level. Included in the rehabilitation costs are (de)mobilization costs, as equipment would not have been present on site.
• Design costs were not included in the rehabilitation as it was assumed that the original LID practice design would be used to inform this work. The annual average maintenance cost does not include rehabilitation costs and therefore represents an average of routine maintenance tasks, as outlined in Table Permeable Pavements: Key Components, Descriptions and Routine I&M Requirements, above. All cost value estimates represent the NPV as the calculation takes into account average annual interest (2%) and discount (3%) rates over the evaluation time periods.
• The costing presented in this section is specific to permeable interlocking concrete pavers (PICP), as defined in the Tool. This product has been selected for costing due to its popularity and well understood maintenance needs.
• For all permeable pavement design variations, the CDA has been defined as 2,000 m² of which 1,000 m² is impermeable pavement draining to the pavers, and 1,000 m² is permeable pavement. The impervious area to pervious area ratio (I:P ratio) used to size the BMP footprint is 1:1, which is in accordance with recommendations in the LID SWM Planning and Design Guide (CVC & TRCA, 2010).
  • The Full Infiltration design does not include a sub-drain and assumes a native sub-soil infiltration rate of 20 mm/h. The base granular reservoir is 350 mm deep and is capable of storing runoff from a 61 mm rain event over the CDA. A monitoring well is included for inspection purposes.
  • The Partial Infiltration design includes a sub-drain and assumes a native sub-soil infiltration rate of 10 mm/h. The base granular reservoir is 350 mm deep and is capable of storing runoff from a 9 mm rain event before the stored volume reaches the perforated underdrain pipe located 50 mm above the native sub-soil. Although a flow restrictor is recommended to maximize infiltration, the cost of this feature is not included due to its relatively low cost.
  • The No Infiltration design includes a sub-drain pipe installed on the bottom of the sub-surface water storage reservoir and an impermeable liner. All other features are the same as the Partial Infiltration design variation.
• Estimates of the life cycle costs of PICP permeable pavements in Canadian dollars per unit CDA ($/m²) are presented in the table below. LID Life Cycle Costing Tool allows users to select what BMP type and design variation applies, and to use the default assumptions to generate planning level cost estimates.
  • Users can also input their own values relating to a site or area, design, unit costs, and inspection and maintenance task frequencies to generate customized cost estimates, specific to a certain project, context or stormwater infrastructure program.
  • For all BMP design variations and maintenance scenarios, it is assumed that rehabilitation of the pavement surface will be necessary when the BMP reaches 30 years of age to maintain acceptable surface drainage performance. Rehabilitation of PICP pavements is assumed to typically involve the following tasks and associated costs:
    • Remove pavers, bedding and joint fill and top 5 cm (2”) of base aggregate and replace with new material that meets design specifications
    • Construction and Assumption inspection and testing associated with rehabilitation work to confirm that materials meet design specifications and installation is acceptable, including compaction and surface infiltration rate testing.

Life cycle cost estimates for all infiltration types of PICP permeable pavements an under minimum and high frequency scenarios (in 2016 $ figures).

Notes:

1. Estimated life cycle costs represent NPV of associated costs in Canadian dollars per square metre of CDA ($/m2).
2. Average annual maintenance cost estimates represent NPV of all costs incurred over the time period and do not include rehabilitation costs.
3. Rehabilitation cost estimates represent NPV of all costs related to rehabilitative maintenance work assumed to be needed after 30 years in service, including those associated with inspection.
4. Full Infiltration design life cycle costs are lower than Partial and No Infiltration designs due to the absence of a sub-drain to construct, inspect and routinely flush.
5. Rehabilitation costs for Full Infiltration designs are estimated to be 54.8% to 55.6% of the original construction costs for High and Minimum Recommended Frequency maintenance program scenarios, respectively.
6. Rehabilitation costs for Partial Infiltration designs are estimated to be 53.5% to 54.3% of the original construction costs for High and Minimum Recommended Frequency maintenance program scenarios, respectively.
7. Rehabilitation costs for No Infiltration designs are estimated to be 47.4% to 48.1% of the original construction costs for High and Minimum Recommended Frequency maintenance program scenarios, respectively.
8. Maintenance and rehabilitation costs over a 25 year time period for the Minimum Recommended maintenance scenario are estimated to be 22.3%, of the original construction costs for Full Infiltration design, 22.6% for Partial Infiltration design, and 20.0% for No Infiltration design.
9. Maintenance and rehabilitation costs over a 25 year time period for the High Frequency maintenance scenario are estimated to be: 39.0% of the original construction costs for Full, 38.9% for Partial Infiltration designs, and 34.5% for No Infiltration designs.
10. Maintenance and rehabilitation costs over a 50 year time period for the Minimum Recommended Frequency maintenance scenario are estimated to be approximately: 1.07 times the original construction cost for Full, 1.06 times the original construction costs for Partial Infiltration designs, and 93.9.% the original construction cost for No Infiltration designs.
11. Maintenance and rehabilitation costs over a 50 year time period for the High Frequency maintenance scenario are estimated to be approximately: 1.43 times the original construction cost for Full, 1.41 times the original construction costs for Partial Infiltration designs, and 1.25 times the original construction cost for No Infiltration designs.

State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include Source, Conveyance and End-Of-Pipe Controls.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

The natural ground material characteristic of or existing by virtue of geographic origin.

Best management practice. State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include: source, conveyance and end-of-pipe controls.

Toronto and Region Conservation Authority

Surface runoff from at-grade surfaces, resulting from rain or snowmelt events.

A hard surface area (e.g., road, parking area or rooftop) that prevents or retards the infiltration of water into the soil.

A mixture of mineral aggregates bound with bituminous materials, used in the construction and maintenance of paved surfaces.

The slow movement of water into or through a soil or drainage system.

Penetration of water through the ground surface.

A broad category of particulate material used in construction, including sand, gravel, crushed stone, slag, recycled concrete and geosynthetic aggregates, and available in various particulate size gradations.

Lake Simcoe Region Conservation Authority

Water ponded on the ground surface.

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

Structure to control the volume or rate of flow of water through or over it.

An alternative practice to traditional impervious pavement, prevents the generation of runoff by allowing precipitation falling on the surface to infiltrate through the surface course into an underlying stone reservoir and, where suitable conditions exist, into the native soil.

The rate at which stormwater percolates into the subsoil measured in inches per hour.

Soil particles with a diameter less than 0.050 mm.

Sustainable Technologies Evaluation Program

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

The total surface area upstream of a point on a stream that drains toward that point. Not to be confused with watershed. The drainage area may include one or more watersheds.

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

An alternative practice to traditional impervious pavement, prevents the generation of runoff by allowing precipitation falling on the surface to infiltrate through the surface course into an underlying stone reservoir and, where suitable conditions exist, into the native soil.

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

A body of water smaller than a lake, often artificially formed.

Box like underground concrete structure with openings in curb and gutter designed to collect runoff from streets and pavement.

A system flow of gully inlets, pipes, overland flow paths, open channels, culverts and detention basins used to convey runoff to its receiving waters. City of Toronto 45 Wet Weather Flow Management November 2006

The downward movement of water through the soil, the downward flow of runoff from the bottom of an infiltration BMP into the soil.

Loss of water from a drainage system as a result of percolation or absorption into the surrounding medium (e.g., the infiltration of water into the native soil through a perforated pipe wall as it is conveyed).

A shallow excavated surface depression containing prepared filter media, mulch, and planted with selected vegetation.

Linear bioretention cell designed to convey, treat and attenuate stormwater runoff. The engineered filter media soil mixture and vegetation slows the runoff water to allow sedimentation, filtration through the root zone, evapotranspiration, and infiltration into the underlying native soil.

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

The technique of removing pollutants from runoff as it infiltrates through the soil.

Gravel, or crushed stone of various size gradations (i.e., diameter), used in construction; void forming material used as bedding and runoff storage reservoirs and underdrains in stormwater infiltration practices.

A perforated pipe used to assist the draining of soils.

An underlying bed filled with aggregate or other void-forming fill material that temporarily stores stormwater before infiltrating into the native soil or being conveyed by an underdrain pipe.

State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include Source, Conveyance and End-Of-Pipe Controls.

Refers to the conditions in which an organism lives and survives or the conditions in which an organism resides. These conditions can be described as aspects of a “physical”, “social” or an “economic” environment, depending on the perspective perceived by the observer.

Low impact development is a stormwater management and land development strategy applied at the parcel and subdivision scale that emphasizes conservation and use of on-site natural features integrated with engineered, small scale hydrologic controls to more closely mimic pre-development hydrologic functions.

A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.