Inlets

Concentrated flow inlets are associated with LID practices such as Bioretention, Stormwater planters, Infiltration trenches and chambers. Sheet flow alternatives include level spreaders, gravel diaphragms and vegetated filter strips. Practices such as permeable paving and green roofs receive precipitation directly, whilst exfiltration trenches are connected directly to conventional storm sewers.

Inlets for BMPs in the right of way should be located:

• At all sag points in the gutter grade
• Immediately upgrade of median breaks, crosswalks, and street intersections.

It is good practice to have several inlets sized to distribute inflow along the length of the practice or between multiple facilities (Offline overflow).

Trench drains	Curb cuts	Inlet sumps	Depressed drains
A long, covered channel that collects directs water into the BMP. An excellent solution for streets where walking across the entire surface is to be encouraged. They can be designed as detectable edges or part of a detectable edge, and may be used to help define curbless or 'complete streets'. Trenches may either be shallow (where runoff volume is less of an issue) or deep and covered by a metal grate. Deeper trench drains may gather sediment and require frequent maintenance. Drains may be configured either perpendicular or parallel to the flow direction of the roadway, collecting runoff and directing to a single inlet in the BMP.	Inlet aprons or depressions increase inflow effectiveness of curb cuts. Steeply angled aprons can be hazardous, especially to people bicycling. Curbside and protected bike lanes along concrete aprons should be at least 1.8 m to give cyclists adequate clear width from the curb and any pavement seams. Aprons can also be marked visually to indicate their perimeter. For aprons into bioretention, the curb may angle into the cell to improve conveyance of gutter flow into the facility. Aprons typically drop 50 mm into the bioretention cell, with another 50 mm drop behind the curb to maintain inflow as debris collects. A depressed concrete apron can be cast in place or retrofitted in by grinding down the existing concrete pavement. Where the curb alignment along the street is straight, the curb opening may optionally have a bar across the top of the inlet.	An inlet sump is recommended to settle and separate sediment from runoff where a large amount of debris is expected. Water drains into a catch basin, where debris settles in its sump. After pretreatment, water drains via a pipe or opening into the BMP. The sump can be directly connected to a perforated underdrain pipe to distribute the flow to the bioretention, supported soil cells or underground practices such a trenches or chambers . Sump inlets should not be sited where pedestrians will have to negotiate with them.	Runoff in the gutter drops into a grate-covered drain before flowing into the BMP. Drain covers must be compatible with bicycling and walking; grid covers are preferred. Depressed drains are a potential solution for bioretention cells on sloped streets where directing runoff into the cell is a challenge. This style of inlet can be combined with a curb cut, to maintain capacity in case debris clogs the grate.
Combination of trench drain and winter shut off gate: King Street, Kitchener, ON Trench drain that outlets to a bioswale at the LSRCA Office in Newmarket, ON Trench drain in parking lot of Evergreen brickworks, Toronto ON Bioretention system, or rain garden with a decorative trench drain cover, in Portland, US Taken in April 2013. Photo credit:EmilyBlueGreen This trench drain has easily opened, hinged sections for maintenance, Singpore	OPSD 605.040 Asphalt Spillway inlet to biofilter swale and road catch basin overflow outlet. County Court Blvd., Brampton, ON. This curb cut has been sawn into existing concrete as part of a retrofit. Note the temporary (erosion log) and permanent stone erosion control measures in place. Mississauga Road, ON. Curb cut used as a controlled overflow route from permeable pavements to a bioretention facility with monitoring well, Lake Simcoe Region Conservation Authority, Newmarket, ON. Curb cut into a bioretention facility in Hinsdale, IL. Stone in the center of the facility reduces erosion and dissipates power inflow around the inlet area. A monitoring/maintenance well can be seen in the foreground. Photo credit: CNT Curb cut into a bioretention facility in Brown Deer, WI. Stone is used to reduce erosion around the inlet area. Photo credit: Aaron Volkening Curb cut into a bioretention facility in Ajax, ON. Stone lined inlet at IMAX site in Mississauga The grading around this inlet prevents flow in the correct direction. i.e. from the pavement onto the grass. Not too critical in this example, as the surface is permeable pavements. Curb cut into a rain garden on a green street in Newmarket, ON. Curb cut leading into a small bioretention cell in Brampton, ON. Curb cut leading to a bioswale in Brampton, ON.	This inlet channels flow from an underground pretreatment unit onto the surface of a large bioswale, Mississauga Road, ON This bioretention facility is sunken from it's surrounding landscape, in part to accommodate the drop the the catchbasin inlet. Elm Drive, Mississauga, ON A clogged inlet at the bioretention facility on Elm Drive in Mississauga in need of maintenance.	Depressed drains: Gallery

External links

https://nacto.org/publication/urban-street-stormwater-guide/stormwater-elements/bioretention-design-considerations/inlet-design/

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

Any form of rain or snow.

Best management practice. State of the art methods or techniques used to manage the quantity and improve the quality of wet weather flow. BMPs include: source, conveyance and end-of-pipe controls.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

Soil, sand and minerals washed from land into water, usually after rain. They pile up in reservoirs, rivers and harbors, destroying fish-nesting areas and holes of water animals and cloud the water so that needed sunlight might not reach aquatic plans. Careless farming, mining and building activities will expose sediment materials, allowing them to be washed off the land after rainfalls.

A shallow excavated surface depression containing prepared filter media, mulch, and planted with selected vegetation.

Ground depression acting as a flow control and water treatment structure, that is normally dry.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

Linear bioretention cell designed to convey, treat and attenuate stormwater runoff. The engineered filter media soil mixture and vegetation slows the runoff water to allow sedimentation, filtration through the root zone, evapotranspiration, and infiltration into the underlying native soil.

Lake Simcoe Region Conservation Authority

A mixture of mineral aggregates bound with bituminous materials, used in the construction and maintenance of paved surfaces.

A bioretention BMP featuring an impermeable liner and underdrain that prevents infiltration of runoff into the underlying native soil; provides sedimentation and filtration of urban runoff as it passes through the mulch layer, engineered filter media and vegetation root zone.

A bioretention cell that features an impermeable liner that collects and treats stormwater through sedimentation and filtration only (i.e., no infiltration).

A shallow constructed channel, often grass-lined, which is used as an alternative to curb and channel, or as a pretreatment to other measures. Swales are generally characterized by a broad top width to depth ratio and gentle grades.

Includes the protection of soil from dislocation by water, wind or other agents.

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

Box like underground concrete structure with openings in curb and gutter designed to collect runoff from streets and pavement.