Difference between revisions of "Swales: TTT"
Jenny Hill (talk | contribs) |
Jenny Hill (talk | contribs) |
||
| Line 3: | Line 3: | ||
[[File:Weir TTT.png|thumb|Weir elements may be incorporated as checkdams]] | [[File:Weir TTT.png|thumb|Weir elements may be incorporated as checkdams]] | ||
It is recommended that swales be modelled | It is recommended that grass and [[enhanced grass swales]] be modelled using the 'Swale' element in the TTT. A 'swale' has to connect two existing elements within the TTT | ||
For detailed scenarios of enhanced swales, the weir element can be incorporated for checkdams. At this time the weirs are seperate elements which must be placed within several distinct swales along a single reach. | For detailed scenarios of enhanced swales, the weir element can be incorporated for checkdams. At this time the weirs are seperate elements which must be placed within several distinct swales along a single reach. | ||
Revision as of 20:05, 18 September 2017
It is recommended that grass and enhanced grass swales be modelled using the 'Swale' element in the TTT. A 'swale' has to connect two existing elements within the TTT For detailed scenarios of enhanced swales, the weir element can be incorporated for checkdams. At this time the weirs are seperate elements which must be placed within several distinct swales along a single reach.
The alternative is to use the 'enhanced swale' within the LID toolbox, but this incorporates fewer design parameters (and also excludes check dams).
| General Info | |
|---|---|
| Upstream Node | Name of node on the inlet end of the swale (higher elevation) |
| Downstream Node | Name of node on the outlet end of the swale (lower elevation) |
| Manning's Roughness | Lower numbers indicate less surface obstruction and result in faster flow. Suggested range for mown grass (dependent on density) 0.03 – 0.06 [1] |
| Upstream Invert (m) | Depth of swale invert above node invert at inlet end of the swale |
| Downstream Invert (m) | Depth or elevation of the swale invert above the node invert at the outlet end of the swale |
| X Section | |
| Maximum Depth (m) | Depth of the swale |
| Bottom Width (m) | Bottom width of the trapezoidal swale For a triangular channel, enter 0 |
| Left Side Slope (m/m) | Left side slope (run/rise). Suggested value of 3 or 4 if design permits. Enhanced swales |
| Right Side Slope (m/m) | Right side slope (run/rise). Suggested value of 3 or 4 if design permits. |
| Seepage (mm/hour) | Infiltration rate of native (or amended) soil |
The TTT also includes an 'enhanced swale' element within the LID toolbox. In version 1.0 this element does not incorporate checkdams and doesn't account for any infiltration capacity.
| Surface | |
|---|---|
| Berm height (mm) | This is the height of the curb which constrains the overland sheet flow of water. Where the bottom of the slope discharges directly into another LID facility without impedance, the value is 0. |
| Surface roughness (Manning’s n) | Lower numbers indicate less surface obstruction and result in faster flow. Suggested range for mown grass (dependent on density) 0.03 – 0.06 [1] |
| Surface slope (%) | If the slope > 3%, consider using small Checkdams or weirs to permit temporary ponding, increase infiltration, and slow flow to reduce erosion. |
| Swale side slopes (run/rise) | Suggested value of 3 or 4 if design permits Enhanced swales |
- ↑ 1.0 1.1 Oregon State Univ., Corvallis. Dept. of Civil, Construction and Environmental Engineering.; Environmental Protection Agency, Cincinnati ONRMRL. Storm Water Management Model Reference Manual Volume I Hydrology (Revised). 2016:233.https://nepis.epa.gov/Exe/ZyPURL.cgi?Dockey=P100NYRA.txt Accessed August 23, 2017.