Source Water Protection

Image of the 19 Source Protection Regions (SPRs) and Source Protection Areas (SPAs) in Ontario (Conservation Ontario, 2022). Visit the Map link here for a higher resolution image.

Overview

Spurred mainly by the Walkerton Tragedy in May of 2000, where 2,500 residents of the town fell ill due to ingesting high levels of E.coli bacteria and 7 individuals died due to poor monitoring and maintenance of the drinking water system, the province (Scarfone, 2020) took major overhauling actions to ensure Ontarians drinking water was adequately protected.

Following an inquiry into the Walkerton event, Justice, O'Connor at the time made over 120 recommendations to better protect the province's drinking water, which have now been implemented and are the foundation of the province's drinking water protection framework. The first of these recommendations was that drinking water should be protected by developing watershed-based source water protection plans, which have been in place since 2006 with the adoption of the Clean Water Act (Government of Ontario, 2021)

Source Water Protection in Ontario

Since the Clean Water Act, 2006 was adopted within the province the original recommendations of the "Walkerton Inquiry" were able to begin to be implemented. The legislation required municipalities protect their drinking water sources and supplies through prevention by developing collaborative large-scale watershed-based source protection plans or source water protection (SWPP) based on monitoring results and the latest science. When the Clean Water Act was first established the province paid for the cost of developing the preliminary SWPPs.

Under the Clean Water Act the legislation describes newly developed source water protection areas and source water protection regions.

• Source Protection Region (SPR): Encompass one or more source protection areas (ex. Credit Valley-Toronto and Region-Central Lake or simply the CTC Region).
• Source Protection Area (SPA): Smaller geographic areas generally based on the watershed boundaries of Ontario's 36 Conservation Authorities

Ontario’s Clean Water Act, 2006 is the primary piece of legislation within the province to ensure that there is a multi-barrier approach to ensure not only clean and safe drinking water, but by ensuring usage is sustainable and protects lakes, rivers, wells and other major sources of freshwater for ~14.5 million residents (Photo Source: Conservation Ontario, 2016)

Under the Clean Water Act local multi-stakeholder source protection committees were developed for each region. Each committee is comprised on the region's leading researchers, professionals and technical personnel that help identify significant current and potential future threats to their local municipal drinking water sources. Their job is to regularly meet and develop preventative plans to address identified and theorized threats (Lake Erie Source Protection Region, 2022)

Source Protection Plans (SPP)

Source protection plans (SPPs) contain a number of policies that are locally developed by their local technical committees aimed at protecting existing and future spruces of adequate drinking water sources for impacted municipalities.

The associations who are reporting and implementing SPP policies and progress annually include:

• Conservation Authorities;
• Municipalities;
• Source protection authorities;
• Local health boards;
• Indigenous groups, committees and governments;
• Local businesses
• The Province of Ontario; and,
• Others (Government of Ontario, 2021)

The Source Protection Committee generally uses varied approaches to protect drinking water sources within each SPR/SPA, which can include:

• Prescribed policy instruments (existing provincial approvals such as Environmental Compliance Approvals and Permits To Take Water);
• Requiring any owners/developers present a formalized risk management plan (negotiated individually);
• Specified land use planning;
• Prohibition of activities that may prove detrimental to SPZs; and/or,
• Current outreach and education activities (webinars, town meetings, pamphlets, online education hubs) (CTC SPR, 2019)

Under the Clean Water Act, 2006 a total of 19 SPRs and SPA's have been established across the province. Each of these 19 SPRs/SPAs contain their own local multi-stakeholder source protection committees across the province which have developed 38 local source protection plans. These specialized plans identify various actions to protect over 450 affected municipal drinking water systems (covering 95% of Ontario's population) (Government of Ontario, 2021).

Ultimately, SPPs are plans to help reduce or eliminate significant drinking water threats within its associated zone/area. These drinking water threats are listed in the following and the SPPS have policies place which must also be enforced. These policies when implemented help to both manage and/or prohibit significant threats as a result of various activities to ensure that they cannot pollute or deplete necessary sources of municipal drinking water within the zone/area.

A road sign to alert motorists that they are entering a provincially protected Drinking Water Protection Zone (SWPZ) to help raise awareness (Photo Source: Conservation Ontario, 2018)

SPRs & SPAs in Ontario

Listed below are 19 different SPRs and SPAs in Ontario, where you can visit each Region's/Area's dedicated Sourcewater protection website for information on their committee members, recent reports, helpful documents, informational videos and the like:

1. Ausable Bayfield Maitland Valley Source Protection Region
2. Cataraqui Source Protection Area
3. CTC Source Protection Region
4. Essex Region Source Protection Area
5. Greater Sudbury Source Protection Area
6. Halton-Hamilton Source Protection Region
7. Lake Erie Source Protection Region
8. Lakehead Source Protection Area
9. Mattagami Region Source Protection Area
10. Mississippi-Rideau Source protection Region
11. Niagara Peninsula Source Protection Area
12. North Bay-Mattawa Source Protection Area
13. Quinte Region Source Protection Area
14. Raisin-South Nation Source Protection Region
15. Saugeen, Grey Sauble, Northern Bruce Peninsula Source Protection Region
16. Sault Ste. Marie Region Source Protection Area
17. South Georgian Bay Lake Simcoe Source Protection Region
18. Thames-Sydenham Source Protection Region
19. Trent Conservation Coalition Source Protection Region

Source Protection Assessment Reports

Each of the 19 aforementioned SPRs & SPAs has an Assessment Report that acts as a 'living technical document' for that given region. The Assessment report includes:

• Recent research findings and scientific information regarding source water protection;
• A brief overview of each impacted watershed within the SPR/SPA;
• Provides a water budget (which is a way to measure the amount of freshwater water enters, is stored, and leaves a watershed);
• Identifies vulnerable areas near key freshwater sources (municipal wells and intakes);
• Identifies the number of significant threats (agricultural practices, sewage sources, fertilizers, etc.) to water quality near wells and intakes; and,
• Identifies areas that could have varied threat levels (low, moderate, high) (CTC SPR, 2019)

Planning Considerations

Inclusion of the tools and atlas

• Recommendations - refer to SPP (pull from B.C's recommended practices)
• Top lessons and maintenance (setback distances / replacing media)

Talk about pretreatment - filtration before being sent directly to groundwater source (bioretention/swale -> infiltration trench) Online vaults from minor system flows (filter and target specific pollutants) - before infiltration.

When planning any new development within a SPR/SPA its important to follow the following four (4) major Steps before moving forward.

1) Identify and Map Vulnerable Areas

The two major areas of significance that are vulnerable to water/groundwater pollution threats are called Wellhead Protection Areas (WHPAs) and Intake Protection Zones (IPZs). New development must note if any of their proposed activities or future actions will cause potential negative impacts on these important municipal sources of freshwater.

Wellhead Protection Areas (WHPAs)

A Wellhead Protection Area (WHPA) is an area located on the ground surface that denotes a specific zone within a known aquifer where fresh groundwater flows to a pumping well. Any detrimental activities/actions that take place in this zone may contribute to pollutions that can infiltrate into the underlying soil below and in turn contaminate said groundwater source for private and municipal wells alike - hence undertaken in this area may release pollutants that could seep into the soil and contaminate the groundwater used by both domestic and municipals wells. As a result, these areas require high levels of monitoring, protection and enforcement. Accordingly, this area warrants greater protection.

The risk to groundwater quality at the well site is determined by the rate at which a specific pollutant/contaminant can infiltrate and travel to the well and the time it would take to remediate the contaminant from the water supply by trained municipal water operators. If a chemical/contaminant spill were to happen a far distance away from a known well, a follow up assessment will be required, this assessment includes:

• Determining whether the contaminant could reach the well in question and the duration of time it may take to reach it.
• Is the contaminant a human, biological or environmental risk or is it simply an aesthetic nuisance?
• Will the concentration of said contaminant exceed the Canadian Water Quality Guidelines (CWQG) for drinking water standard or the Provincial Water Quality Network's (PWQMN) standard (i.e. chloride levels)?
• Will the current mitigation/treatment protocols currently used be sufficient enough to mitigate/remove the harmful concentration levels of said contaminant from reaching the well?
  • If said mitigation/treatment protocol needs to be amended and time allows a mitigation system can be installed to limit the movement of said chemical to the well or the water treatment process at the receiving Water Treatment Plant (WTP) can be modified to sufficiently decrease the concentrations being received

When it comes to WHPAs once size does not fit all, there are multiple zones that extend in an irregular radius around a well to ensure adequate protection of the source water protection area, which is divided into five (5) zones based upon contaminant travel time within groundwater sources:

1. WHPA-A – an area of 100 metre radius around the wellhead
2. WHPA-B – the zone through which it takes groundwater to travel between two years and the 100 metre distance
3. WHPA-C – the zone through which it takes groundwater to travel between five and two years
4. WHPA-D – the zone through which it takes groundwater to travel between 25 and five years
5. WHPA-E – the area on ground surface through which surface water flows in two hours to a point close to the well. This wellhead protection area is only delineated when studies have shown that surface water can relatively easily seep through the soil and impact the quality of the water at the well. This situation is known as groundwater under the direct influence of surface water, or a GUDI well
   (Halton-Hamilton Source Protection Region, 2010CTC SPR, 2019))

Site Considerations

Installation type	Depth to high water or bedrock (m)i	Ratio of impervious drainage area to permeable facility footprint area	Native soil infiltration rate (mm/hr)ii	Head (m)iii	Space %iv	Slope %v	Applicable in pollution hotspotsvi	Set backs	Karstvii	Drinking Water Source Protection wellhead protection area time of travel
Rain barrels	Not a constraint	Not applicable	Not a constraint	1	0	NA	Yes	None	Yes	None
Cisterns	Not a constraint	Not applicable	Not a constraint	0	0	0	Yes	None	Yes	None
Roof downspout disconnection	Not a constraint	4:1 or less	Decompaction if < 15 mm/hr	0.5	5 to 20	1 to 5	Yes	Building Foundation	Yes	None
Infiltration trenches or Infiltration chambers	1	5:1 to 20:1	Not a constraint	1 to 2	0 to 1	<15 %	Noix	4m- Building Foundation Underground Utilities, Trees, Drinking Water Wellhead Protection Areas	No	2 yr
Bioretention	1 (infiltrating); Not a constraint (non-infiltrating)	5:1 to 15:1	Decompaction and underdrain recommended if < 15 mm/hr (infiltrating)	1 to 2	5 to 10	0 to 2	No (infiltrating)ix; Yes (non-infiltrating)	4m- Building Foundation Underground Utilities, Trees, Drinking Water Wellhead Protection Areas	No (infiltrating); Yes (non-infiltrating)	2 yr (infiltrating); None (non-infiltrating)
Stormwater planters	Not a constraint	5:1	Not a constraint	1 to 2	2 to 5	0 to 2	No (infiltrating)ix; Yes (non-infiltrating)	Building Foundation, Trees	No (infiltrating); Yes (non-infiltrating)	2 Yr (infiltrating); None (non-infiltrating)
Vegetated filter strips	Not a constraint	4:1 or less	Decompaction if < 15 mm/hr	0 to 1	15 to 20	1 to 5	Noix	None	Yes	None
Permeable pavements	1 (infiltrating); Not applicable (non-infiltrating)	0 to 1:1	Underdrain recommended if < 15 mm/hr (infiltrating)	0.5 to 1	0	1 to 5	No (infiltrating)ix; Yes (non-infiltrating)	4m-Underground Utilities Drinking Water Wellhead Protection Areas	No (infiltrating); Yes (non-infiltrating)	2 Yr (infiltrating); None (non-infiltrating)
Enhanced swales (featuring check dams)	1	5:1 to 10:1	Decompaction if < 15 mm/hr	1 to 3	5 to 15	0.5 to 6	Noix	4m- Building Foundation Underground Utilities	No	2 Yr
Bioswales (Dry swales)	1 (infiltrating); Not applicable (non-infiltrating)	5:1 to 15:1	Decompaction and underdrain recommended if < 15 mm/hr (infiltrating)	1 to 3	5 to 10	0.5 to 6	No (infiltrating)ix; Yes (non-infiltrating)	4m (3m if impermeable liner is used) Building foundation, Underground utilities, Drinking Water Wellhead Protection Areas	No (infiltrating); Yes (non-infiltrating)	2 Yr (infiltrating); None (non-infiltrating)
Exfiltration trenches	1	5:1 to 10:1	Not a constraint	1 to 3	0	< 15%	Noix	4m- Building Foundation Underground Utilities, Trees, Drinking Water Wellhead Protection Areas	No	2 Yr
Stormwater tree trenches	1	5:1 to 15:1	Underdrain recommended if < 15 mm/hr	1 to 2	5 to 10	0 to 2	Noix	4m- Building Foundation Underground Utilities, Drinking Water Wellhead Protection Areas	No	2 yr

Notes
i Minimum depth between the base of the facility and the elevation of the seasonally high water table or top of bedrock
ii Infiltration rate estimates based on measurements of hydraulic conductivity under field saturated conditions at the proposed location and depth of the practice
iii Vertical distance between the inlet and outlet of the LID practice
iv Percent of open pervious land on the site that is required for the LID practice
v Slope at the LID practice location
vi Suitable in pollution hot spots or runoff source areas where land uses or activities have the potential to generate highly contaminated runoff
vii Suitability in areas of karst geologic formations
viii Drinking Water Source Protection wellhead protection area time of travel
ix May be allowed under special circumstances and if appropriate mitigation actions are taken - please contact your local Source Protection Region (SPR) or Source Protection Area (SPA) for further information. You can find your associated SPR/SPA based on your location here and then visit their site here

Design Features

LID BMPs

The drainage area of a river.

An area of land that drains into a river or a lake. The boundary of a watershed is based on the elevation (natural contours) of a landscape.

Any person, agency or group who has a direct interest in the purpose of a proposed undertaking.

The mathematical expression of the water balance.

The liquid waste from domestic, commercial and industrial establishments. City of Toronto Wet Weather Flow Management Guidelines November 2006 49

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

The technique of removing pollutants from runoff as it infiltrates through the soil.

A shallow excavated surface depression containing prepared filter media, mulch, and planted with selected vegetation.

A shallow constructed channel, often grass-lined, which is used as an alternative to curb and channel, or as a pretreatment to other measures. Swales are generally characterized by a broad top width to depth ratio and gentle grades.

That storm drainage system which is frequently used for collecting, transporting, and disposing of snowmelt, miscellaneous minor flows, and storm runoff up to the capacity of the system. The capacity should be equal to the maximum rate of runoff to be expected from the minor design storm which may have a frequency of occurrence of one in 2, or 5 years. The minor system may include many features ranging from curbs and gutters to storm sewer pipes and open drainage ways.

The slow movement of water into or through a soil or drainage system.

Penetration of water through the ground surface.

Layer of rock or soil that holds or transmits water.

(1) Something that pollutes, especially a waste material that contaminate air, soil, or water. (2) Any solute or cause of change in physical, chemical or biological properties that render water unfit for a given use.

A hard surface area (e.g., road, parking area or rooftop) that prevents or retards the infiltration of water into the soil.

The total surface area upstream of a point on a stream that drains toward that point. Not to be confused with watershed. The drainage area may include one or more watersheds.

The natural ground material characteristic of or existing by virtue of geographic origin.

The rate at which stormwater percolates into the subsoil measured in inches per hour.

Structures constructed of a non-erosive material, such as suitably sized aggregate, wood, gabions, riprap, or concrete; used to slow runoff water. Can be employed in practices such as bioswales and enhanced grass swales.

Linear bioretention cell designed to convey, treat and attenuate stormwater runoff. The engineered filter media soil mixture and vegetation slows the runoff water to allow sedimentation, filtration through the root zone, evapotranspiration, and infiltration into the underlying native soil.

The upper surface of the zone of saturation, except where the surface is formed by an impermeable body.

Subsurface water level which is defined by the level below which all the spaces in the soil are filled with water; The entire region below the water table is called the saturated zone.

The rate at which stormwater percolates into the subsoil measured in inches per hour.

A parameter that describes the capability of a medium to transmit water.

Low Impact Development. A stormwater management strategy that seeks to mitigate the impacts of increased urban runoff and stormwater pollution by managing it as close to its source as possible. It comprises a set of site design approaches and small scale stormwater management practices that promote the use of natural systems for infiltration and evapotranspiration, and rainwater harvesting.

The portion of water precipitated onto a catchment area, which then flows as surface discharge from the catchment area past a specified point.

Water from rain, snow melt, or irrigation that flows over the land surface.

Initial capturing and removal of unwanted contaminants, such as debris, sediment, leaves and pollutants, from stormwater before reaching a best management practice; Examples include, settling forebays, vegetated filter strips and gravel diaphragms.

Refers to the conditions in which an organism lives and survives or the conditions in which an organism resides. These conditions can be described as aspects of a “physical”, “social” or an “economic” environment, depending on the perspective perceived by the observer.