Bioretention: Filter media

From LID SWM Planning and Design Guide
Revision as of 17:56, 11 October 2018 by Jenny Hill (talk | contribs)
Jump to navigation Jump to search
Sandy filter media mix.
Filter media being used for an online bioretention swale (also of previous, more sandy specification)

It is recommended that the mixture comprises:

One of these two blend options
Blend A: Drainage priority Blend B: Water quality priority
Application Higher I/P ratio
Proportions

3 parts sand
1 part organic soil components and additives

3 parts sand
2 parts topsoil
1 part sand organic soil components and additives

Filter media should be obtained premixed from a vendor and meet all municipal, provincial and federal environmental standards. Mixing of sand, topsoil and compost should be done in a manner that preserves topsoil peds. The mixture should be free of stones, stumps, roots, or other debris larger than 50 mm diameter. Samples of the filter media should be dried, ground and tested to ensure they meet the following specifications:

Bioretention filter media
Characteristic Criterion Recommended method
Texture <15 % fines Hygrometer
Organic matter (OM) 5 - 10 % ASTM D2974-14, Standard test methods for moisture, ash and organic matter of peat and other organic soils.
Phosphorus 12 - 40 ppm As measured by the 'Bray' method. Alternatives include 'Mehlich I or III', or 'Olsen'. Results from these are not directly translatable.[1]
Cationic exchange capacity(CEC) 10 meq/100 g ASTM D7503-10, Standard test method for measuring the exchange complex and cation exchange capacity of inorganic fine grained soils.
Hydraulic conductivity > 25 mm/hr
< 250 mm/hr
Falling head or constant head KSAT

Note that grain size distribution does not form part of the recommended acceptance criteria. Whilst this information may be useful in designing blends, the disconnect between hydraulic conductivity and the uniformity of gradation makes it far less important then measuring the hydraulic conductivity directly[2]

Sand[edit]

Particle size distribution graph for ASTM C33 sand, as described in table
  • Coarse sand for LID construction shall be washed clean and free of toxic materials.
  • The pH of the sand shall be ≤ 7.0.
  • The coarse sand shall have a fineness modulus index between 2.8 and 3.1 according to ASTM C33/C33M, or otherwise meet the gradation below.
Particle size distribution
Sieve Percent passing
9.5 mm 100
4.75 mm (No.4) 95 - 100
2.36 mm (No.8) 80 - 100
1.18 mm (No.16) 50 - 85
0.60 mm (No.30) 25 - 50
0.30 mm (No.50) 5 - 30
0.15 mm (No.100) 0 - 10
0.075 mm (No.200) ≤ 3

Topsoil[edit]

  • Topsoil may be material that was stripped from the project site and stored in stockpiles for re-use, or material imported to the site from a supplier provided the physical and chemical characteristics are within acceptable ranges.
  • Topsoil shall be in compliance with Ontario Regulation 153/04 Record of Site Condition standards for soil quality or as amended through Ontario Management of Excess Soil - A Guide for Best Management Practices.
  • Soil laboratory reports shall certify the material to be suitable for re-use on residential, parkland, institutional, industrial, commercial, or community landscapes for the germination of seeds and the support of vegetative growth.

The factors to consider in determining if a topsoil is suitable for use as planting soil for a vegetated stormwater practice, or use in producing a bioretention filter media mixture include the following:

  • Must be friable and capable of sustaining vigorous plant growth;
  • Must be free from toxic material and roots, stones or debris over 50 mm (2") in diameter;
  • Should not have been passed through sieves or screens smaller than 50 mm (2”) to avoid eliminating peds;
  • Should have a Loamy Sand, Sandy Loam, Sandy Clay Loam, Loam or Silty Loam soil texture;
  • For use as planting soil for a vegetated stormwater practice , the topsoil must contain a minimum of 5% organic matter by dry weight or be amended so, through addition of an organic soil conditioner;
  • For use in producing bioretention filter media Blend B (water quality treatment priority), the topsoil must contain at least 9%, and not greater than 36% clay-sized particles and at least 2% organic matter by dry weight.
  • Must have a pH of between 6.0 and 8.0;
  • Must have a sodium absorption ratio less than 15;
  • Must have a cationic exchange capacity greater than 10 milliequivalents per 100 grams (meq/100 g).

Specify that 4 litre samples of topsoil, from each source to be drawn upon, be provided to the consultant for visual inspection, along with topsoil quality test results from an accredited soil testing laboratory, or a quality assurance certificate from the supplier.

We recommend a planting soil or filter media depth of 300 mm to support grasses, 600 mm for shrubs and perennials, and 1000 mm for trees.

Organic components[edit]

This is the first big opportunity to manage phosphorus export from a bioretention or stormwater planter system. Whilst compost is the most common ingredient, designers working in sensitive watersheds are encouraged to explore the alternatives listed below. Some of these materials may be combined 50:50 with compost to balance the nutrients required by the plants and the potential for leaching of excess nutrient.

Compost[edit]

Compost is the most widely used organic component. It's use in bioretention facilities is well established and documented. Low-phosphorus composts should always be sought for use in low impact development facilities, including bioretention. These are typically created from feedstocks including yard, leaf, and wood waste, and must exclude manures, biosolids, and food scraps.[3]
Compost Specifications

Even low-phosphorus composts are known to export phosphorus over many years. The use of compost is not recommended in watersheds for which phosphorus pollution is a concern. There are alternatives which have undergone field study, each of which has a number of benefits and potential concerns:

Organic soil components
Material Benefits Concerns
Coconut coir[4] Doesn't leach phosphorus Requires importation
Wood chip Doesn't leach phosphorus
Promotes nitrogen removal from water
-
Peat Moss Doesn't leach phosphorus Sustainability controversial
Shredded paper [5] (see: Pittmoss)


Wood derivatives[edit]

https://www.unh.edu/unhsc/sites/default/files/media/unhsc_bsm_spec_2-28-17_0.pdf https://www.unh.edu/unhsc/sites/unh.edu.unhsc/files/STONE%20THESIS%20FINAL.pdf https://jbioleng.biomedcentral.com/articles/10.1186/s13036-017-0057-4 (focus on denitrification)

Additives[edit]

Typically these components would make up 5- 10 % by volume of the filter media mixture.

A number of granular amendments have been demonstrated to improve nutrient removal from discharge water in BMPs such as bioretention systems, stormwater planters, absorbent landscapes, sand filters or green roofs.

There are two primary processes involved, chemical precipitation and adsorption. Both mechanisms are ultimately finite, but have been shown in come cases to make significant improvements on the discharged water quality over several years.

In our effort to make this guide as functional as possible, we have decided to include proprietary systems and links to manufacturers websites.
Inclusion of such links does not constitute endorsement by the Sustainable Technologies Evaluation Program.
Lists are ordered alphabetically; link updates are welcomed using the form below.

Filter Media Additives
Material Benefits Potential concerns
Biochar Renewable
Enhances soil aggregation, water holding capacity and organic carbon content
Currently expensive
Energy intensive to produce
Some sources say ineffective for phosphorus removal
Bold & GoldTM Documented total phosphorus removal of up to 71%[6] Proprietary
Iron filings or Zero valent iron (ZVI) Proven phosphorus retention
Retained phosphorus is stable
May harm plants[7]
Removal efficiency declines with increased concentration of incoming phosphorus
Red sand or Iron-enriched sand Proven phosphorus removal
Also removes TSS
Poor orthophosphate removal in hypoxic or anoxic conditions
Smart SpongeTM Removes phosphorus, as well as TSS, fecal coliform bacteria and heavy metals
Non-leaching
1-3 year lifespan, after which the product is removed as solid waste
Proprietary
Sorbtive MediaTM High phosphorus removal efficiency Proprietary
Water treatment residuals Waste product reuse Quality control (capabilities depend on source, treatment methods, storage time)

  1. Sawyer JE, Mallarino AP. Differentiating and Understanding the Mehlich 3, Bray, and Olsen Soil Phosphorus Tests 1. http://www.agronext.iastate.edu/soilfertility/info/mnconf11_22_99.pdf. Accessed August 1, 2017.
  2. CRC for Water Sensitive Cities. (2015). Adoption Guidelines for Stormwater Biofiltration Systems: Appendix C - Guidelines for filter media in stormwater biofiltration systems.
  3. Hurley S, Shrestha P, Cording A. Nutrient Leaching from Compost: Implications for Bioretention and Other Green Stormwater Infrastructure. J Sustain Water Built Environ. 2017;3(3):4017006. doi:10.1061/JSWBAY.0000821.
  4. Rheaume, A., Hinman, C., and Ahearn, D. (2015). “A Synthesis of Bioretention Research in Pacific Northwest.” Herrera, <http://www.modularwetlands.com/new/wp-content/uploads/2015/11/2-Bioretention-Synthesis-2015-DAhearn.pdf>
  5. Urban Drainage and Flood Control District. (2010). “Bioretention.” <http://udfcd.org/criteria-manual/volume-3/t-03-bioretention/> (Mar. 15, 2018).
  6. Hood A, Chopra M, Wanielista M. Assessment of Biosorption Activated Media Under Roadside Swales for the Removal of Phosphorus from Stormwater. Water. 2013;5(1):53-66. doi:10.3390/w5010053.
  7. Logsdon SD, Sauer PA. Iron Filings Cement Engineered Soil Mix. Agron J. 2016;108(4):1753. doi:10.2134/agronj2015.0427.